Bedienungsanleitung Sharp UL-C09EA-W (Seite 9 von 92) (Deutsch, Englisch, Französisch, Italienisch, Spanisch, Polnisch)

787872

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

FAN button

• Pressing this button can select fan speed as: AUTO, SPEED 1 ( ), SPEED

2 ( ), SPEED 3 ( ).

NOTE:

 Under Auto speed, air conditioner will select proper fan speed

automatically according to ambient temperature.

 Fan speed can't be adjusted under dry mode.

X-FAN button

• Press this button under cool and dry mode to start up x-fan function.

Press this button again to cancel X-FAN function.

• Under Auto speed, air conditioner will select proper fan speed

automatically according to ambient temperature.

• Fan speed can't be adjusted under dry mode.

• When X-FAN function is on, if the air conditioner is turned o, fan will

still operate at low speed for a while to blow the residual water inside

the air duct.

• During X-FAN operation, press X-FAN button to turn o X-FAN function.

Indoor fan will stop operation immediately.

SLEEP button

• Press sleep button to enter into sleep mode. If the controller operates

at cooling mode, after sleep mode is started up, preset temperature will

increase by 1°C within 1 hour; preset temperature will increase by 2°C

within 2 hours and then the unit will operate at this temperature until

turned o.

• Sleep function is only available for cooling mode. SLEEP function can be

set together with OFF timer.

TIMER button

• When unit is on, press this button to set Timer O. T-OFF and H icon

will blink. Within 5s, press + or - button to adjust the time for Timer

O. Pressing + or - button once will increase or decrease the time by

0.5hours. Hold + or - button for 2 seconds, time will change quickly.

Release the button after your required set time is reached. Then press

TIMER button to conrm it. T-OFF and H icon will stop blinking.

• When unit is o, press this button to set Timer On. T-ON and H icon will

be blinking. Within 5 seconds, press + or - button to adjust the time for

Timer On. Pressing + or - button once will increase or decrease the time

by 0.5 hours. Hold + or - button for 2 seconds, time will change quickly.

Release the button after your required set time is reached. Then press

TIMER button to conrm it. T-ON and H icon will stop blinking.

• Canceling the timer function: If Timer function is set up, press TIMER

button once to review the remaining time. Within 5 seconds, press

TIMER button again to cancel this function.

• ON timer and OFF timer cannot be set together.

NOTE:

 Range of time setting is: 0.5~24 hours.

 The interval between two motions can't exceed 5 seconds, otherwise the

remote control will exit setting status.

Functions by Combination Buttons

Child lock function

Press "+" and "-" buttons simultaneously can turn on or turn o child lock

function. When child lock function is started up, child lock indicator on

remote controller is ON. If you operate the remote control, remote control

won't send signal.

This function works only for remote controller, the buttons on the unit

itself can not be locked.

Temperature display switchover function

Under OFF status, press "-" button and "MODE" button simultaneously can

switch between °C and °F.

Light function

You can turn o or turn on the light of the unit's control panel. Under

switch-on or switch-o status, point the remote control to the unit's signal

receiver and you may hold "+" and "FAN" buttons simultaneously for 3

seconds to set the light on or o.

Installation of batteries

1. Press and slide the back cover to open the battery compartment of the

remote control.

2. Insert two AAA (1,5 V) size batteries (included). Make sure the (+) and

(–) ends of the batteries match the (+) and (–) ends indicated in the

battery compartment.

3. Close the battery compartment cover.

NOTE:

During operation, point the remote control signal sender at the receiving

window on indoor unit.

 The distance between signal sender and receiving window should be no

more than 8 meters, and there should be no obstacles between them.

 Signal may be interfered easily in the room where there is uorescent

lighting or wireless telephone; in these situations, move the remote

control closer to the appliance for reliable operation.

 Replace new batteries of the same model when replacement is required.

 If you will not be using the unit for a long time, remove the batteries

from the remote control.

 If the display on remote control is fuzzy or there's no display, please

replace batteries.

Care and Maintenance

WARNING!

• Before cleaning the air conditioner, please turn o the unit and disconnect

power. This will ensure that the risk of an electric shock is eliminated.

• Do not wash air conditioner with water. This will ensure that the risk of an

electric shock is eliminated.

• Do not use volatile liquid (such as thinner or gas) to clean the air conditioner.

Otherwise, it may damage the surface.

• Do not use liquid or corrosive detergent clean the appliance and do not

splash water or other liquid onto it, otherwise,it may damage the plastic

components, or even cause electric shock.

Clean outer case and grille

Clean outer case:

If there's dust on the surface of outer case, please use soft cloth to wipe it.

If the outer case is very dirty (such as grease), please use neutral detergent

to wipe it.

Clean grille:

To clean the grille itself, use a soft brush.

Clean lter

(Do not touch the ns to prevent injury.)

1. Remove the lter

Press the clasp as shown in the gure, and then remove the lter;

Sharp UL-C09EA-W Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info