Bedienungsanleitung Sharp XL-UH12H (Seite 4 von 16) (Englisch)

526649

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

E-3

After checking all the connections have been made

correctly, plug the AC power lead of this unit into the wall

socket. If you plug in the unit first, the unit will enter the

stand-by mode.

Note:

Unplug the AC power lead from the wall socket if the unit

will not be in use for a prolonged period of time.

Caution:

● Replace all old batteries with new ones at the same

time.

● Do not mix old and new batteries.

● Remove the batteries if the unit will not be used for a

long period of time. This will prevent potential damage

due to battery leakage.

● Do not use rechargeable batteries (nickel-cadmium

battery, etc.).

● Installing the batteries incorrectly may cause the unit to

malfunction.

● Batteries (battery pack or batteries installed) shall not

be exposed to excessive heat such as sunshine, fire or

the like.

Notes concerning use:

● Replace the batteries if the operating distance is

reduced or if the operation becomes erratic. Purchase

2 “AAA” size batteries (UM/SUM-4, R03, HP-16 or

similar).

● Periodically clean the transmitter on the remote control

and the sensor on the unit with a soft cloth.

● Exposing the sensor on the unit to strong light may

interfere with operation. Change the lighting or the

direction of the unit if this occurs.

● Keep the remote control away from moisture, heat,

shock, and vibrations.

Press the ON/STAND-BY button to turn the power on.

● If you turn off and on the main unit with volume set to

16 or higher, the volume will start at 16.

● If you turn the unit off then on again with the volume

level set to less than 16, it will turn on again at the level

set.

Turn the volume knob towards VOLUME +/– (on main unit)

or press VOL +/– (on remote control) to increase or

decrease the volume.

System connection (continued)

■ Speaker connection

● Connect the black wire to the minus

(–) terminal, and the red wire to the

plus (+) terminal.

● Use speakers with an impedance of

8 ohms or more, as lower

impedance speakers can damage

the unit.

● Do not mistake the right and the left

channels. The right speaker is the

one on the right side when you face

the unit.

Incorrect

● Do not let the bare speaker wires touch each other.

● Do not allow any objects to fall into or to be placed in the

bass reflex ducts.

● Do not stand or sit on the speakers. You may be injured.

RIGHT LEFT

RIGHT

SPEAKERS

LEFT

■ AC power connection

Remote control

■ Battery installation

Open the battery cover.

Insert the batteries according to the direction indicated

in the battery compartment.

When inserting or removing the batteries, push them

towards the (–) battery terminals.

Close the cover.

General Control

VOLU ME

ON/STAND-BY

■ To turn the power on

After use:

Press the ON/STAND-BY button to enter the power stand-

by mode.

■ Volume auto set-in

■ Volume control

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Sharp XL-UH12H Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Sharp XL-UH12H

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info