Bedienungsanleitung Siemens CCBB1345 (Seite 2 von 4) (Deutsch, Englisch, Holländisch)

39250

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

Data and desi

n sub

ect to chan

Technolo

ies: Fire and Securit

Products GmbH & Co. oHG

English

Step 7: Synchronization

Package contents Operation and storage

LL and INT mode are available for this camera. The

factory default is INT. User can change the setting to

Line lock mode in combination with an AC power

source by changing #3 pin of DIP SW (11) to LL.

Due to the physical nature of the CCD there is a

possibilty of picture noise when using the camera in

LL-mode under low-light conditions. Usage of

INT-mode is recommended.

• CCD camera Do not operate or store the unit in following

locations: • C/CS-mount adapter

• Instruction manual • Extremely hot or cold places

• Close to sources of strong magnetism

Important

• Close to sources of powerful electromagnetic

radiation such as radios or TV transmitters.

This quick start guide is only intended for use by

installers who have an adequate working knowledge

of video systems!

• In humid or excessively dusty places

• Where exposed to mechanical vibrations.

Step 8: SHARP/SOFT selection

• Close to fluorescent lamps or objects reflecting

light.

Use DIP SW (11) pin 4 to select::

This guide outlines the most important information

about the camera. It is vital that you read this

manual carefully before any operation of camera.

Selection of picture sharpness (SHARP, SOFT).

• Under unstable or flickering light sources

Step 9: Connecting power supply

Care and maintenance

Connect the power supply cable to the power

connectors (7) (see figure E):

Camera parts

The camera is maintenance-free.

See figure B, C, D and E

Use a clean soft piece of cloth to wipe small

amounts of dirt or dust from the camera body. If the

unit tends to get very dirty, the camera should be

placed within a protective housing.

Caution

1. Back focus adjust ring

If you are using a DC supply, make sure the

polarity is correct. Incorrect connection may

cause malfunction and/or damage to the

camera.

2. Back focus lock screw

3. Tripod mount hole

4. IRIS connector

5. Power indicator

Specifications

Select one of the following options

6. BNC connector for composite video output

Active pixels: 752(H) x 582(V)

7. Power cord (or terminal)

 For 12 V DC:

Scanning system: 2:1 interlace CCIR

8. V-PHASE pot

 Connect shielding to terminal GND (12).

Hor. Resolution: 580 TVL

9. LEVEL pot

 Connect 12 V (-) to terminal =DC 12V- (13).

Min. Illumination: 0.15 Lux @F1.2

10. Video/ DC Lens selection

 Connect 12 V (+) to terminal =DC 12V+ (14).

S/N-Ratio: > 50 dB

11. Mode setting switch

 For 24 V AC:

Synchronisation: Internal or Line-Lock

12.

 Connect 24 V (~) cables to terminals

~AC 24V (13 and 14).

Video Output: composite

Power requirement: DC 12V/AC 24V ±10% or

~AC90 – 260 V, 50 Hz

Installing the camera

 Connect shielding to terminal GND (12).

Step 1: Mounting the camera

Power consumption: 3 VA

Adjusting camera settings

Camera weight: -LP: 450 g

1. Attach the camera to a wall bracket, ceiling

bracket, pan/tilt mount or other suitable fitting.

Use of the ¼ inch thread tripod mount hole (3) to

prevent the camera from rotating.

-MP: 550 g

Setting flange focal distance

Operating temperature: -10 ~ +50 ℃

Caution

Risk of damage to camera! Ensure that the locking

screw is loosened before turning the adjustment

screw. Avoid forcing the adjustment screw.

2. Mount the cable guide to the camera to ensure

that the cables are kept securely in place (see

figure A).

Fixed focus lenses

Step 2: Screw the lens onto the camera

1. Loosen the locking screw (2) by turning it

counter-clockwise.

Select one of the following options:

 For C-mount lens: add a CS-C adapter to the

camera, then screw the lens directly onto the

camera.

2. Open the diaphragm to its fullest extent

manually. If the images are overexposed, or for

lenses with automatic diaphragm adjustment:

reduce lighting levels or hold a neutral grey filter

in front of the lens.

 For CS-mount lens: Screw the lens directly

onto the camera (no adapter ring required).

Step 3: Connecting the lens

3. Set the focus to ∞.

Two type of lens (DC or Video controlled) can be

used for this camera. However, please take note to

select DC or VIDEO lens using switch (10) before

connecting the lens and make sure the wire

connection for each type lens is conform to the pin

assignment below.

4. Point the camera at an object (at a distance of at

least 2000 times the focal length of the lens).

5. Adjust the backfocus ring (1), alter the flange

focal distance until the image is clearly in focus.

6. Re-tighten the locking screw (2).

Varifocal lenses

Then connect the control cable to the IRIS

connector (4, side or rear) on the camera.

Video Lens DC Lens

1. +12V 1. Damp-

2. NC 2. Damp+

3. VIDEO 3. Drive +

4. GND 4. Drive-

1. Loosen the locking screw (2) by turning it

counter-clockwise.

2. Open the diaphragm to its fullest extent

manually If the images are overexposed, or for

lenses with automatic diaphragm adjustment:

reduce lighting levels or hold a neutral grey filter

in front of the lens.

3. Set the focus to ∞.

Step 4: Connecting video signal

4. Select the wide angle (min. focal length) setting.

 For composite video: connect BNC connector

VIDEO OUT (6) to the monitor with a coax cable.

5. Point the camera at an object (at a distance of at

least 2000 times the focal length of the lens).

Step 5: Backlight compensation:

6. Adjust the backfocus ring (1), alter the flange

focal distance until the image is clearly in focus.

Backlight compensation is available by switching pin

1 of (11) to ON

7. Select the telescopic (max. focal length) setting

and adjust the focus to improve image clarity.

Step 6: AES/AI selection

8. Reset the camera to the minimum focal length

(wide angle) and fine adjust the flange focal

distance using the adjustment ring (1).

Use DIP SW (11) pin 2 to select:

Set to ON: AES (auto electronic shutter) mode

Set to OFF: AI mode (shutter speed=1/50 sec)

9. Re-tighten the locking screw (2).

Siemens CCBB1345 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info