Bedienungsanleitung Siemens CN878G4B6B (Seite 39 von 56) (Englisch)

790199

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

Disposal en

Fault Cause and troubleshooting

"Fill water tank" ap-

pears in the display

even though the wa-

ter tank has been

filled.

Malfunction

▶Do not use deionised or filtered water.

→"Before using for the first time", Page14

The sensor is defective.

▶Call the after-sales service.

→"Customer Service", Page40

Buttons are flashing. Condensation has formed behind the control panel.

No action required. As soon as the condensation has evaporated, the buttons no longer

flash.

"Plopping" sounds

can be heard when

cooking with steam.

Water vapour requires the cold/heat effect for frozen food.

No action required.

The appliance hums

during operation and

after it is switched off.

Functional test of the pump creates operating noise.

No action required.

The appliance hums

or clicks when the

control panel is

opened.

Removing the control panel creates operating noise.

No action required.

During simple mi-

crowave operation,

the cooking compart-

ment becomes hot.

The drying function is switched on.

The interior lighting

does not work.

The LED light is defective.

Note:Do not remove the glass cover.

▶Call the after-sales service.

→"Customer Service", Page40

Maximum operating

time reached.

To prevent an unwanted permanent operation, the appliance automatically stops heating

after several hours if the settings are unchanged. A message appears in the display.

The point at which the maximum operating time is reached is determined by the corres-

ponding settings for an operating mode.

1. To continue operation, switch off the appliance with ⁠ first.

2. Then use ⁠ to switch on the appliance and set the required operation.

Tip:To prevent the appliance from switching off when you do not want it to, set a cooking

time.

A message with "D"

or "E" appears in the

display, e.g. D0111

or E0111.

The electronics have detected a fault.

1. Switch the appliance off and on again.

aIf the fault was a one-off, the message disappears.

2. If the message appears again, call the after-sales service. Please specify the exact error

message when calling.

→"Customer Service", Page40

The cooking result is

not satisfactory.

Settings were unsuitable.

Setting values, e.g. temperature or cooking time, depend on the recipe, quantity and food.

▶Next time, set lower or higher values.

Tip:A lot of information about the food preparation and corresponding setting values

can be found on our website www.siemens-home.bsh-group.com .

27 Disposal

27.1 Disposing of old appliance

Valuable raw materials can be reused by recycling.

1. Unplug the appliance from the mains.

2. Cut through the power cord.

3. Dispose of the appliance in an environmentally

friendly manner.

Information about current disposal methods are

available from your specialist dealer or local author-

ity.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens CN878G4B6B Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info