Bedienungsanleitung Siemens DH18400M (Seite 11 von 76) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch, Polnisch)

652239

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Operating instructions

Please read and observe the detailed safety instructions

at the start of these instructions!

■ Important: The appliance may never be exposed to frost!

Risk of electric shock!

Switch off the mains voltage supply immediately if

a fault occurs.

■ Immediately shut off the cold water supply to the appli-

ance should it leak.

Getting to know your appliance

The continuous-ﬂow heater heats the water as it ﬂows

through the appliance. The appliance only consumes power

during this period.

Operating elements

The continuous-ﬂow heater has two heat settings:

e Economy setting – two thirds power

II Intensive setting – full power

The e setting is ideal for:

Wash basin

Shower

Bidet

The II setting is used in combination with a thermostatically-

controlled premixer, for high temperatures or for large vol-

umes of water, e. g. for:

Dishwashing

Cleaning

Bath tub

Operating the appliance

Turn on the hot-water tap

The continuous-ﬂow heater switches on and heats the water

when the hot-water tap is turned on (Fig. E, 1.).

It switches off again when the tap is turned off.

Notes (not applicable for DH12...): When the water tap is

turned on only slightly, the continuous-ﬂow heater will oper-

ate at half power in both of the preselected settings (e, II).

When the water tap is turned on fully, the appliance will oper-

ate at full, preselected power.

Increasing the water temperature

Slightly close the hot-water tap (Fig. E, 2.).

Decreasing the water temperature

Turn on the cold-water tap (Fig. E, 3.).

Startup after a water cutoff

■ Disconnect the appliance from the mains supply (remove

the fuses in the fusebox).

■ Turn on the hot-water tap until the air is purged from the

pipe.

■ Reinstall the fuses.

The appliance is ready for operation.

Saving energy

Use the “e” setting whenever possible.

For wash basins: Open the corner valve to such an extent

that only the lower heat setting switches on.

Winter operation

Note: It is possible in winter that the supply temperature of

the water is reduced and the required outlet temperature is

no longer achieved.

■ In order to compensate for this temperature reduction,

please reduce the water quantity on the tap until the re-

quired water temperature is achieved.

Cleaning

Simply wipe the appliance with a damp cloth.

Do not use acidic or abrasive cleaning materials.

Notes: It is normally not necessary to descale the appliance.

However, extremely hard water and the frequent ﬂows of

very hot water can cause the appliance to scale up. In this

case please contact our after-sales service.

After-sales service

If you call the after-sales service for assistance, please specify

the E no. and FD no. of your appliance.

These numbers are found on the inside of the swing-out con-

trol panel of the continuous-ﬂow heater.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens DH18400M Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info