Bedienungsanleitung Siemens DH18400M (Seite 12 von 76) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch, Polnisch)

652239

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

A fault, what to do?

Attention!

Repairs must only be carried out by an authorised technician. Improper repairs can lead to risk of serious injury to

the user.

If your appliance does not operate as required, it is often due to a very minor problem. Please check whether you can remedy

the fault yourself by using the following guidelines. You will save yourself the costs of an unnecessary visit by customer service

personnel.

Fault Cause Solution Who

Water ﬂow-rate is too low.

The appliance does not

switch on.

The ﬁlter in either the water tap or

the showerhead is clogged.

Remove the ﬁlter and either clean it or

descale it.

Customer

The ﬁlter in the corner valve is

clogged.

Get a servicing expert to clean the

ﬁlter.

Servicing expert

The corner valve is clogged. Turn on the hot-water tap fully and

open and close the corner valve several

times. Then clean the ﬁlter in the water

tap.

Customer

The water is not sufﬁciently

warm.

The fuse in the house electrical

installation has tripped/blown.

Check the fuse in the fusebox. Customer

The appliance‘s automatic circuit

breaker has been tripped.

Get the appliance‘s automatic circuit

breaker checked by an electrician. Check

the permissible supply temperature.

Servicing expert

The power limit has been reached.

Water ﬂow-rate is too high and/or

the cold water supply temperature

is too low.

Reduce the ﬂow-rate on the tap. Customer

By a qualiﬁed professional:

use the corner valve to regulate the

ﬂow-rate.

Check the ﬂow-rate limiter or replace it

with a smaller one.

Servicing expert

The second stage in the appliance

does not switch on (the audible

“clicking” is missing).

Remove the ﬁlter in the tap and either

clean it or descale it.

Customer

Clean the ﬁlter in the corner valve

(Fig. A, 4.).

Servicing expert

The continuous-ﬂow heater

switches off during the

drawing-off of water, result-

ing in a reduction in the

water temperature:

Swelling seal in the warm

water tap

A non-swelling sealing material must

be used in the warm water tap.

Customer

Winter operation:

The desired water tempera-

ture leaving the tap is no

longer reached.

The supply temperature has

reduced.

Reduce the water ﬂow on the taps

until the desired water temperature is

reached.

Customer

If the fault could not be eliminated, please call customer service.

Disposal

This appliance is labelled in accordance with Euro-

pean Directive 2012/19/EU concerning used elec-

trical and electronic appliances (waste electrical

and electronic equipment – WEEE).

The guideline determines the framework for the

return and recycling of used appliances as appli-

cable throughout the EU.

Please ask your specialist retailer about current

disposal facilities.

Guarantee

The guarantee conditions for this appliance are as deﬁned by

our representative in the country in which it is sold.

Details regarding these conditions can be obtained from the

dealer from whom the appliance was purchased. The bill of

sale or receipt must be produced when making any claim un-

der the terms of this guarantee.

Subject to change without notice.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens DH18400M Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info