Bedienungsanleitung Siemens EY645CXB1E (Seite 13 von 24) (Englisch)

790748

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Flex Zone en

|Flex Zone

Fl ex Zone

You can use each flex zone as a single hotplate or as

two independent hotplates, as required.

It consists of four inductors that work independently of

each other. If using the flexible cooking zone, only the

area that is covered by cookware is activated.

Advice on using cookware

To ensure that the cookware is detected and heat is

distributed evenly, correctly centre the cookware:

As two independent hotplates

The flexible cooking zone is used like two independent

hotplates.

Activating

See section ~ "Operating the appliance"

As a single hotplate

Using the entire cooking zone by connecting both

hotplates.

Linking the two hotplates

1. Set down the cookware and select the required heat

setting using one of the two hotplate controls for the

flexible cooking zone.

The heat setting lights up in the display for the

previously activated hotplate.

2. Touch the ß symbol. The indicator lights up.

The flexible cooking zone has now been activated.

Changing the power level

Use the same control as above to change the power

level.

Adding new cookware

Set down the cookware and touch the ß symbol twice.

The new cookware is detected and the previously

selected heat setting remains the same.

Notes

■If the cookware on the active hotplate is moved or

lifted from it, the hotplate begins an automatic

search and the heat setting that was previously

selected is retained.

■If you turn a hotplate control that was not previously

used to select the heat setting, the flexible cooking

zone is deactivated. In this case, both hotplates

continue to function independently of one another,

with each hotplate operating at the previously

selected heat setting.

Unlinking the two hotplates

Touch the ß symbol. This deactivates the flexible

cooking zone. The hotplate continues to function as two

independent hotplates.

Note: If you switch the hob off and then subsequently

switch it on again, the flexible cooking zone is

converted back to two independent hotplates.

As a single hotplate

Diameter smaller than or equal to 13 cm

Place the cookware on one of the four posi-

tions that can be seen in the illustration.

Diameter greater than 13 cm

Place the cookware on one of the three

positions that can be seen in the illustration.

If the cookware takes up more than one

hotplate, place it starting on the upper or

lower edge of the flexible cooking zone.

As two independent hotplates

The front and rear hotplates each have two induc-

tors and can be used independently of each other.

Select the required heat setting for each of the

hotplates. Use only one item of cookware on each

hotplate.

Recommendations

If the hob has more than one flexible

cooking zone, place the cookware on

top so that it covers only one of the flex-

ible cooking zones.

Otherwise, the hotplates will not be

activated as intended and the cooking

result will not be satisfactory.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens EY645CXB1E Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens EY645CXB1E

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info