429227
13
Zoom out
Zoom in
Vorherige Seite
1/24
Nächste Seite
Service Guideline HiPath Workpoint Clients
HiPath Xpressions Compact V1.0
Issue 1.0 from 02/02 Page 13 of 24
Installation
The HiPath Xpressions Compact boards are handled like other HiPath 3000 boards. HiPath
Xpressions Compact (P8/P8R and S8/S8R) boards may not be inserted or removed while the
system is running; the HiPath Xpressions Compact (L8) and (L24) boards may be removed while
the system is running.
Attention: packing protection covering:
Before starting up the board, the packing protection covering on the HiPath Xpressions Compact
board must be removed. When the board is returned or sent in (transport) for repair, this packing
protection covering (cardboard block) must be attached again.
System Requirements
The following requirements must be met for the installation of the HiPath Xpressions Compact:
an available slot in HiPath 3700/3750 systems for one HiPath Xpressions Compact
(L24) not together with an SLMO24 on the same PCM bus, in
HiPath 3350/3550 wall systems only the lower slots
one HiPath Xpressions
Compact board
per system: HiPath Xpressions Compact (P8): S30122-Q7379-X100
HiPath Xpressions Compact (P8R): S30122-Q7379-Z100
HiPath Xpressions Compact (S8): S30122-Q7379-X
HiPath Xpressions Compact (S8R): S30122-K7379-Z
HiPath Xpressions Compact (L8): S30122-Q7380-X100
HiPath Xpressions Compact (L24): S30122-Q7380-X
a ferrite bead: only in HiPath 3700/3750 systems. Part number: C39022-Z7000-C7
HiPath Xpressions Compact software: HE100V.01.1xx and later (P50038-P0100-A1-*)
PBX hardware: HiPath 3000 V1.2 with control unit (CBCPR, CBCC, CBCP, CBRC, CBRP)
PBX software: HiPath 3700/3750: HE550S.53.7xx and later (P30370-P855-A610-*)
HiPath 3500/3550: HE550U.53.7xx and later (P30370-P856-A610-*)
HiPath 3300/3350: HE550T.53.7xx and later (P30370-P857-A610-*)
HiPath 3000 ManagerE: HA550B.53.xxx and later (P50038-P1510-A1-*)
Commissioning/start-up
Software and languages (voice prompts/system announcements) have already been installed on
the HiPath Xpressions Compact board. After the boards have been inserted, the start-up to
standby mode occurs (default start-up).
The proper system start-up can be monitored with the diagnostic LEDs.
Then the administration can be performed with the HiPath 3000 Manager E.
Customer Orientation:
The customer is given a brief introduction (basic training, 0.5 hour).
13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Siemens hipath 3500 v8 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info