Bedienungsanleitung Siemens RDE100.1RFS (Seite 3 von 4) (Englisch)

555888

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

3/4 Operating Instructions CB1B1425en_01 / 2014-11-26 Siemens Building Technologies

Option 2: Time switch with the same 7-day settings

(P11=1)

Set

–

Mode

You can set the time switch so that all settings

apply to the 7 weekdays.

Example:

1 2



Visible bars: Control to Comfort temperature

 Invisible bars: Control to Economy

temperature

Proceed as follows:

1) Set the parameter (P11=1). Please refer to

section "Do you want to change

parameters".

2) Press Set and select

AUTO

3) Press Ok to confirm.

4) Time switch for Mon (1) - Sun (7) is

displayed.

5) Press Ok to initiate time programming.

During programming:

6) Press Mode to select the operating mode

(Comfort or Economy) or

7) Press + or – to set the time in steps of 15

minutes for the selected operating mode.

8) Press Ok to save the time switch.

9) Press Mode or wait for the program to exit

automatically.

Option 3: Time switch with 5-2-day settings (P11=2)

Factory default of 7-day time switch

Default

value

Day/s Comfort mode Economy mode

Mo (1) –

Fr (5)

6:00 – 8:00 hr

17:00 – 22:00 hr

22:00 – 6:00 hr

8:00 – 17:00 hr

Sa (6) –

Su (7)

7:00 – 22:00 hr 22:00 – 7:00 hr

Do you want to pair transmitter and

receiver?

–

Learn

Mode

The RDE100.1RF communicates with the

RCR100RF at a frequency of 433 MHz.

To pair transmitter and receiver, proceed as

follows:

RCR100RF receiver setting:

1) Press and hold the LEARN button on the

RCR100RF for at least 3 seconds and

then release it.

2) Red and green LEDs flash alternately to

indicate receiver is in learning mode.

RDE100.1/RF transmitter setting:

3) On the transmitter, set the parameters

(refer to section "Do you want to change

parameters?").

4) Check to ensure that parameter P19 is not

0, because this would mean that the

wireless function is disabled. By default,

parameter P19 is 1.

5) Proceed to parameter P20. Press Mode

and parameter P20=0 (OFF) flashes.

Adjust the value by pressing + to change

to P20=1 (ON), then press Mode to

confirm.

6) During the stages of wireless learning, the

LCD displays "rF" and "Lrn". Wait for time

out, and the transmitter exits the

parameter setting mode.

Successful wireless learning:

7) The green LED on the RCR100RF flashes

for 10 minutes to indicate that the receiver

has successfully completed wireless

learning.

Recommendation:

8) Additional test to ensure the wireless

signal is fine:

On the RDE100.1/RF, change the

operating mode by pressing Mode or

change the setpoint by pressing + or –.

On the RCR100RF, the green LED should

flash for 3 seconds before changing to

constantly green. At the same time,

observe your radiator, boiler or heater

indication (if it has one) to ensure that it

changed the operating mode.

9) If step 7 or 8 is working fine, this means

you have successfully paired the units.

Unsuccessful wireless learning:

10) If the RCR100RF fails to receive wireless

data, the red LED starts to flash **.

Repeat steps 1 to 8 until pairing is

successful.

Note:

Always start receiver learning before starting

pairing with the transmitter.

The units must be placed such that transmitter

and received signals have limited external

wireless interference.

**In normal operation, if a drop in wireless

communication occurs due to unforseeable

noise, just leave the receiver and it will recover

automatically.

The pairs are saved even if there is a power

shut down. Communication restarts

automatically after several minutes without any

user action.

set

–

mode

You can set Monday - Friday and Saturday -

Sunday at the same time.

Example:

1 2

 Visible bars: Control to Comfort temperature

 Invisible bars: Control to Economy

temperature

Proceed as follows:

1) Set the parameter (P11=2). Please refer

to section "Do you want to change

parameters".

2) Press Set and select

AUTO

3) Press Ok to confirm.

4) Time switch for Mon (1) – Fri (5) is

displayed.

5) Press + or – to select Mon (1) – Fri ( 5) or

Sat (6) - Sun (7).

6) Press Ok to confirm the selected period

and initiate time programming.

During programming:

7) Press Mode to select the operating mode

(Comfort or Economy) or

8) Press + or – to set the time in steps of

15 minutes for the selected mode.

9) Press Ok to save the time switch.

10) Repeat steps 5-9 for the other period if

necessary or

11) Press Mode or wait for the program to exit

automatically.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens RDE100.1RFS Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens RDE100.1RFS

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info