Bedienungsanleitung Siemens TE501505 (Seite 12 von 117) (Englisch, Holländisch, Französisch, Italienisch)

508124

Zoom out

Zoom in

Vorherige Seite

1/117

Nächste Seite

4. Press and hold the start button (10)

for at least 5 seconds. The set number

of LEDs will light up to indicate that

the selected water hardness has been

saved successfully.

Important: If a water lter is used (special

accessory order no. 467873), proceed as

follows, see “Water lter” on page 10.

Note: If no button is pressed within

90 seconds, the appliance switches to

stand-by mode without saving the new

settings. In this case, the previously saved

water hardness setting is retained.

Automatic switch-off

Here you can set the period of time after

which the appliance should switch off auto-

matically following the last drink preparation.

A time between 15 minutes and 4 hours can

be set. The default time is 1 hour, but this

can be shortened to save energy.

1. Turn the rotary

knob (13) to position

2. Press and hold buttons B (11) and A

(12) simultaneously for at least 5 sec-

onds. The time after which the appliance

should switch off is indicated by the

number of LEDs that now light up.

3. Now press the start button (10) repeat-

edly until the required number of LEDs

light up to indicate the switch-off time:

D = 15 minutes

D and E = 30 minutes

D, E and F = 45 minutes

D, E, F and G = 1 hour

D, E, F, G and H = 2 hours

D, E, F, G, H and I = 4 hours

4. Press and hold the start button (10) for

at least 5 seconds. The set number of

LEDs will light up to indicate that the

selected switch-off time has been saved

successfully.

Note: If no button is pressed within

90 seconds, the appliance switches to

stand-by mode without saving the new

settings. In this case, the previously saved

switch-off time is retained.

Setting the brewing temperature

The brewing temperature can also be set.

1. Turn the rotary

knob (13) to position

2. Press and hold buttons B (11) and

A (12) for at least 5 seconds. The set

brewing temperature is indicated by the

number of LEDs that now light up.

3. Now press the start button (10) repeat-

edly until the required number of LEDs

light up to indicate the temperature:

LED D = low

LED D and E = medium

LED D, E,and F = high

4. Press and hold the start button (10) for

at least 5 seconds. The set number of

LEDs will light up to indicate that the

selected temperature has been saved

successfully.

Note: If no button is pressed within

90 seconds, the appliance switches to

stand-by mode without saving the new

settings. In this case, the previously saved

brewing temperature setting is retained.

Adjusting the grind settings

The selector (3) for grind setting adjusts the

grind settings from coarse to ne.

Warning!

Adjust the grinding unit only while it is run-

ning! Otherwise the appliance may be dam-

aged. Do not reach into the grinding unit.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens TE501505 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Siemens TE501505

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info