Bedienungsanleitung Siemens TJ10100 (Seite 29 von 131) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

473258

Zoom out

Zoom in

Vorherige Seite

1/131

Nächste Seite

Cleaning and maintenance

Control panel and body of the

appliance

When necessary:

❏ Use soapy water or a mild cleaning product.

Dry with a soft cloth.

Warning!

Do not use solvents or abrasive

detergents.

Cleaning the ironing dummy

When necessary or when the dummy is

clearly dirty, the ironing dummy can be

laundered together with your shirts. Use a mild

detergent and a programme for delicate

garments at 40

❏ Do not use fabric softeners or starch.

❏ The ironing dummy can only be dried

naturally (do not use a tumble drier).

Warning!

The ironing dummy cannot be ironed. Fit it

straight back onto the shirt ironer when

dry.

The ironing dummy assembly consists of the

cover material (outer ironing dummy) and the

airbags. The airbags are located inside the

outer ironing dummy and are attached to the

frame independently.

Warning!

Allow the shirt press to cool down before

removing the ironing dummy.

Removing the ironing dummy

❏ Close the flaps on the button band adjuster.

❏ Remove the short sleeve button arm straps

if necessary.

❏ Remove the cuff adjusters by realising the

snap fastener.

❏ Completely loosen the adjustment cords on

the bottom right-hand side of the ironing

dummy.

❏ Fully open the collar adjuster.

❏ Open the collar support.

❏ Lightly press the clip on the back of the

head upwards. Fig. 16.

❏ Remove the upper head section from back

to front. 10, Fig. 2.

❏ Unlock the button band adjuster: Pull the

unlocking ring upwards. Fig. 17.

Warning!

The button band adjuster tilts forwards.

Support it with one hand.

❏ Open the two adjustment cords in the head

area, which is now accessible. Extract them

from their guides. Fig. 18.

❏ Open the cord fixture on the rear edge.

Extract them from their guide. Fig. 19.

On the front, the cord is fitted behind the

button band and secured with the guides

fitted for this purpose.

❏ Turn the collar adjuster knob to its vertical

position.

❏ Grip the ironing dummy from the bottom

and carefully pull upwards.

❏ Pull the ironing dummy from front to back

over the collar adjuster. Fig. 20.

❏ You hold now the ironing dummy cover.

Open the snap fasteners which join the

sleeves of the ironing dummy to the

airbags.

The airbags are still on the frame and need to

be removed:

❏ Open the six snap fasteners on the

shoulders, the snap fasteners in cross

formation on the front and the snap

fasteners around the left-hand tube on the

front at the bottom.

❏ Release the adjustment cord fixture at the

bottom of the airbags. Extract them from

the guide groove.

The ironing dummy and the airbags can now

be washed.

Fitting the ironing dummy

Make sure that nothing enters the air ducts

which are now accesible.

It is essential that the ironing dummy be

fitted correctly in order to obtain optimum

ironing results.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Siemens TJ10100 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info