1. Individual response depends on hair type as well as biological factors that may aect hair growth patterns. Some users may respond quicker or slower
than the average number of treatments.
2. One cannot expect permanent epilation in a single or even double treatment sessions. The duration of the resting period for hair follicles also
depends on the body area.
10. How To Use Flash&Go™
10.1. Flash&Go™ Setup
1. Remove the Flash&Go™ hair removal device, and other components from box.
2. Plug the power cord into the Flash&Go™ Device socket.
3. Plug the other end of the power cord into an electrical outlet.
4. All six LED lights will blink on and o, one after the other, in a circle.
Your Flash&Go™ is now ready to start.
10.2. Treating with Flash&Go™ for the first time
1. The skin should be shaved, clean, dry and free of any powders, antiperspirants or deodorants.
2. Press the central button briefly. The Energy level 1 led will turn on.
About 1 second later, the Ready Indicator Light will turn on. The device is now set to deliver the lowest energy
level pulses. The device is ready for you to trigger the first pulse.
3. If you wish to change the energy level, press the CENTRAL BUTTON quickly and repeatedly to increase the
energy level from 1 to 5 and from 5 directly back to 1, cyclically, until the desired energy level is set. The Energy
Level indicator Lights will indicate the energy level setting. (See “Energy Level” frame).
Energy Level
Energy level determines the intensity of the Flash&Go™ light pulse delivered to your skin, from the
lowest level (1) to the highest level (5). Corresponding indicator lights on the control panel represent
the increases in energy. As energy level increases, so do hair removal results as well as the risk of possible
side eects and complications.
Always start your first Flash&Go™ hair removal session at the lowest energy setting.
If you experience little or no discomfort during and after the hair removal session using the lowest energy
level, raise the energy level by one indicator light at the next session, and so on for each subsequent session.
Do not raise the energy level if you experience abnormal discomfort during or after
treating with Flash&Go™ (See section 8 - “Risks of Using Flash&Go™”).
Do not raise the energy level during a hair removal session even if you experience no
discomfort. Discomfort may also appear sometime after the session.
Whenever Flash&Go™ is turned on; its energy level will automatically be reset to the lowest energy level.
Only one Energy Level indicator Light will be on.
To set the energy level, press the central Button repeatedly to increase the energy level. After reaching level
5, an additional press will bring the level back down to Level 1, and so on, cyclically. The number of Energy
Level indicator Lights will coincide with the change in energy level.
4. Apply the TREATMENT SURFACE to the skin, making sure the skin is spread evenly and smoothly and
the TREATMENT SURFACE is in full contact with the skin. Make sure the Ready Indicator Light starts
blinking slowly.
5. Press the Pulse Trigger. The device will first determine the color of your skin.
If the color of the skin is light enough for safe application, the device will flash a pulse of light onto your
skin. You will see a bright flash of light and simultaneously hear a subtle pop sound, which is a normal
noise for the device. You may feel a mild sensation of warmth and tingling.
Flash&Go™ will immediately recharge for the next pulse. After a few seconds (depending on the set
energy level) the Ready Indicator Light will turn on again and start blinking.
If you see no light pulse, and the Ready Indicator Light blinks rapidly, this is now the SKIN COLOR
WARNING INDICATOR LIGHT alerting that your skin tone is too dark for safe application. Try using
the device on a dierent body part or contact Silk’n support.
6. Move the TREATMENT SURFACE to another area of skin.
Administer one pulse at a time at your chosen energy level. Use the pressure marks the device just made in
your skin to guide you for proper positioning of the next pulse, avoiding both gaps and overlaps between pulses.
Flash&Go™ can be applied in two ways: “Pulsing” and “Gliding”.
7. Repeat the process starting again with Step 5.
PULSING
When Pulsing, administer one pulse at a time at your chosen energy level. Use
the pressure marks the device just made in your skin to guide you for proper
positioning of the next pulse, avoiding both gaps and overlaps between pulses.
Covering skin areas
Treatments should be administered in rows, starting at one end of each row and
progressing sequentially towards the other end. This technique allows better
control of skin coverage, and helps you avoid treating the same area more than
once or overlapping skin areas. Ideal body areas for Flash&Go™ use include the
underarms, bikini line, arms and legs and below cheekbones line.
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Silkn Flash and Go Compact wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.
