Bedienungsanleitung Silkn Flash and Go Compact (Seite 8 von 29) (Englisch)

685067

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

1514

English

If your skin blisters or burns, STOP USE IMMEDIATELY!

10.3. What to Expect when treating with Flash&Go™?

For many people, using Flash&Go™ may be their ﬁrst experience with a light-based device designed for home

use. Flash&Go™ is simple to use, and hair removal sessions go by quickly. During a Flash&Go™ session it is

normal to experience and feel:

A Flash of Light – The bright light of Flash&Go™ will not harm the eyes when applied to non-facial sites,

and special eye-protection is not needed when using Flash&Go™.

A Fan Noise – The cooling fan in Flash&Go™ sounds similar to a hairdryer. This is normal.

A Pop Sound with Each Pulse – When a pulse of HPL™ light is activated, it is normal to hear a subtle pop

sound simultaneously with the ﬂash of light.

Moderate Pressure of the Treatment area – This is necessary and helpful for placement of adjacent pulses

of light, and is part of the unique safety features of Flash&Go™.

A Sensation of Warmth and Tingling – During each pulse of light, it is normal to feel a mild sensation of

warmth and tingling from the light energy. Remember it is important to always use low energy settings for

initial hair removal sessions. You may feel some warmth for up to an hour after your Flash&Go™ session.

Some Mild Red or Pink Color – During and just after your Flash&Go™ session it is not uncommon to

see some very mild, pink-like color of the skin. This is usually most noticeable around the hairs themselves.

However if you see full redness of the skin, blistering or burns, stop use of Flash&Go™ immediately.

GLIDING

Alternatively, if you choose the Gliding method, hold the PULSE TRIGGER down continuously, and

slide the device smoothly along the treated area. Please note that this method is best applied when

working with low energy pulses. This way, the device takes only 1-1.5 seconds to recharge between

pulses and provides a nonstop sequence of ﬂashes.

In both methods of treatment you are cautioned not to treat the same area of skin more than once

per hair removal session! Treating the same area of skin more than once per session increases the

likelihood of adverse eects.

Gliding should be applied while holding the PULSE TRIGGER down continuously, and using a light

sliding motion, smoothly moving the device along the treated area. The treatment is then

administered quickly and more eciently. Even though Gliding is usually done using low energy

pulses for fast recharge, it is still essential to control skin coverage and avoid double treatments.

When applied to the skin, the Flash&Go™ TREATMENT SURFACE is designed to create temporary

pressure marks on the treated area. These visible marks can be used for proper positioning of the

device for treatment sessions.

Skin care following hair removal session

Do not expose the treated areas of skin to the sun. Be sure to carefully protect the

treated skin with sunscreen, throughout the hair removal period and for at least 2 weeks

following the last Flash&Go™ session.

Side eects and complications

Some patients may experience pigmentation changes resulting from treating with Flash&Go™. These eects, if

they occur, are generally mild and transient.

10.4. After treating with Flash&Go™

When a Flash&Go™ session has been completed, turn Flash&Go™ with an extended press of the CENTRAL

BUTTON. Be sure to remember the last energy level setting you used, as it will not be restored when turning

Flash&Go™ on again.

Unplug the power cord from the electrical outlet.

After each hair removal session, it is recommended that you clean your Flash&Go™ device, especially the Treatment

surface (See section 11.1: “Cleaning Flash&Go™”).

After cleaning, it is recommended you store your Flash&Go™ device in its original box, and keep it away from water

If you experience any complication (See section 8 – “Risks of using Flash&Go™”)

please contact your physician immediately.

11. Flash&Go™ Maintenance

11.1. Cleaning Flash&Go™

After each hair removal session, it is recommended that you clean your Flash&Go™ device, and especially the

treatment surface.

Unplug Flash&Go™ before cleaning.

Use a dry, clean cloth and a specially formulated cleaner for electronic equipment to gently wipe the

Flash&Go™ outer shell, and especially the treatment surface.

Never immerse Flash&Go™ or any of its parts in water!

This device is to be orderly disposed of when reaching End of Life stage. In this way the device’s valuable

materials are recycled and the environmental burden avoided.

Deliver your old equipment to the nearest electronic waste collection point for safe and ecient disposal.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Silkn Flash and Go Compact Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info