Bedienungsanleitung Silvercrest IAN 313492 SPM 2000 A1 (Seite 24 von 98) (Deutsch, Englisch, Holländisch, Französisch, Polnisch, Schwedisch)

752906

Zoom out

Zoom in

Vorherige Seite

1/98

Nächste Seite

24 GB/IE

ingredients which are

impeding

the mixing paddle

If maintenance is required, please

contact the service point.

Before each use, please check

the mains cable 3, the plug, the

mixing chamber 1, the mixing

paddle 5 and the other remov-

able parts for damage. If you

ﬁnd damage, please contact the

service address for a replacement.

prevent hazards, ensure that

all elements

have been ﬁxed in

the correct place before you con-

nect the product to the power

supply.

Do not use the microwave or

other sources of heat to disinfect

the product. This could cause

deformation and defects.

Do not clean the product with

steel wool, scouring agents or

corrosive liquids.

Do not expose this device to

sunlight for prolonged periods.

This could cause decolouration.

Do not heat any parts of this

product.

Before ﬁrst use

To prevent hazards, make sure that the device

is complete and the device, mains plug and

mains cable 3 are in good condition after

unpacking to rule out possible damage.

The device is packaged to protect it from trans-

port damage.

Carefully remove the device from the retail

packaging.

Remove all parts of the packaging and remove

the protective ﬁlm from the display.

Thoroughly clean the device and all accessories

as speciﬁed in chapter „Cleaning and care“.

To do so, you will ﬁrst have to disassemble the

device. Follow the instructions in the chapter

„Disassembling the product“.

After it has been thoroughly cleaned and re-as-

sembled (see chapter „Assembly“), set up the

pasta machine in the vicinity of a safety socket.

Make sure it is easily accessible.

Furniture nowadays is coated with a variety of

varnishes and plastics, and is

treated with the

most diverse of care products

. It is therefore im-

possible to rule out that some of these substances

may contain components which would attack

and soften the rubber feet of the housing 2. If

necessary, place an anti-slip pad under the

pasta machine.

Place the device on a suitable surface.

Connect the mains cable 3 with the socket on

the back of the device.

Connect the device to the safety socket.

Disassembling the product

Make sure that the device is switched oﬀ and

unplug the mains plug from the socket before

disassembling.

Remove the lid 4 from the housing 2 by op-

erating the release catch and then pulling the

lid 4 upwards using the handle.

Turn the shaping disk holder 9 anticlockwise

and remove it from the pressing tube 8.

Unscrew both ﬁxing screws

by turning them

anticlockwise at the same time, until the front

panel 6 can be removed from the housing 2

without diﬃculty.

Pull the pressing tube including the auger 8

7 out of the mixing chamber 1.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Silvercrest IAN 313492 SPM 2000 A1 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info