766896
14
Zoom out
Zoom in
Vorherige Seite
1/109
Nächste Seite
12 GB
Overheating protection
The device has an overheating protection
system. If the motor becomes too hot, the de-
vice automatically switches itself off:
1. Switch off the device.
2. Pull out the mains plug3.
3. Allow the device to cool down to room
temperature.
When the device has cooled down suffi-
ciently, it can be switched on again.
8.3 Switching the device on/
off and selecting speed
WARNING! Risk of material damage!
~The mixing mechanism must not be op-
erated continuously for longer than
10 minutes at a time. You must then al-
low the device to cool down to room
temperature.
NOTE:
the device may move slightly while
you are processing large quantities of dough.
1. Switch the device on by turning the
speed control2 clockwise.
2. Start at a slightly lower speed, and slowly
increase to the desired speed (see “Over-
view of functions” on page 9).
3. Reduce the speed to speed 1 - 2 when
you are adding ingredients during oper-
ation through the filling opening10.
4. Set the speed control2 to 0 to switch
the device off.
NOTE: above all, the ideal speed depends
on the consistency of the material being
blended. The more liquid the contents, the
faster you can blend them.
8.4 Pulse function
By turning the speed control2 to the po-
sition Turbo, you can briefly increase
the speed to the highest setting (8).
9. Dismantling the
device
DANGER from rotating parts!
~Turn off the device and unplug the
mains plug3 from the wall socket be-
fore disassembling the device.
Lifting up the drive arm
1. Press the unlock button1 and fold up
the drive arm12 until it engages and
the unlock button1 pops out again.
Removing the mixing tool
2. Push the mixing tool4/6/7 slightly up-
wards and turn it anticlockwise until it
can be pulled off the axle13.
Removing the splash guard
3. Turn the splash guard11 towards the
open lock symbol until it can be re-
moved.
Removing the mixing bowl
4. Turn the mixing bowl5 towards the
open lock symbol until it can be re-
moved.
Lowering the drive arm
5. Press the unlock button1 and move the
drive arm12 all the way down. The un-
lock button1 pops out again.
__360499_2010_B6.book Seite 12 Freitag, 5. Februar 2021 11:57 11
14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln
1

Forum

silvercrest-ian-360499-skm-600-b2

Suche zurücksetzen

  • Ou trouver des pièces detachée (gouet de rechange) Eingereicht am 11-9-2023 17:08

    Antworten Frage melden

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Silvercrest IAN 360499 SKM 600 B2 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info