Bedienungsanleitung Silvercrest SAS 150 A1 - IAN 71494 (Seite 8 von 29) (Englisch)

575514

Zoom out

Zoom in

Vorherige Seite

1/29

Nächste Seite

8 GB/IE/CY

Use the appliance with the supplied accesso-

ries only. No claims under the warranty nor a

liability for damages will be accepted if they re-

sult from improper or incorrect use of the slicer.

Before the First Usage

First steps

Carefully remove the electric Multi-Purpose

Slicer from its packaging, remove all packag-

ing materials and keep them together with the

main packaging.

Clean the electric Multi-Purpose Slicer before it

comes into contact with any foodstuﬀs (see also

the chapter “Cleaning”).

Setting up the appliance

Specific safety advice on the

placing of the appliance

1. Never set the electric Multi-Purpose Slicer up

on a hot surface or near an open ﬂame.

2. Ensure that the power cable

does not pass

over hot or sharp-edged objects.

3. Do not allow the power cable

to become

kinked or trapped and do not wrap it around

the electric Multi-Purpose Slicer.

Set the electric Multi-Purpose Slicer up on a

ﬂat, non-slip surface close to a power socket.

Unwind the required length of power cable

Insert the plug into the power socket.

Place the food carriage

on the supporting

table with guide slot

(see Fig. B). Now

press the on the blade cover

high standing

side down, so that the holding clamps (on the

underside of the food carriage

) engage. En-

sure that these have correctly engaged, in that

you check the mobility of the food carriage. Pull

to the front for removal of the food carriage

from the guide slot

and lift it from the sup-

port table

Push the food holder plate

on to the food

carriage

Place the catch tray

below the support

table

and on the housing such that the

sliced foods can fall in there directly and with-

out hindrance after being cut.

Adjust the inﬁnite slice-thick-

ness setting (see Fig. D)

Through variable tightenings of the adjusting

screws

you can determine the movement rate

of the inﬁnite slice-thickness setting

Screw both of the adjusting screws

tight

with the screwdriver

Check, by turning the inﬁnite slice-thickness

control knob

, to see if the desired movement

rate is suitable.

If it is not,

- loosen both adjusting screws

for a lighter

movement rate or

- tighten both adjusting screws

further for a

stiﬀer movement rate.

Operation

Working advice

Specific safety advice for

slicing and for the handling of

the appliance

1. Never touch the cuttingblade

when the slic-

er is in operation!

There is a risk of grave personal injury!

2. Always use the food carriage

and the food

holder plate

(Exception: very large pieces

of foodstuﬀ).

Press the pieces of food to be sliced forward

using the food holder

3. Use the slicer only for cutting normal house-

hold foods and not for other purposes. Do not

use the slicer for cutting deep-frozen foods,

bones, foods with large kernels or for the

slicing of still packaged foods.

4. Never use the slicer continuously for more than

10 minutes .

OperationSafety / Before the First Usage / Operation

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Silvercrest SAS 150 A1 - IAN 71494 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Silvercrest SAS 150 A1 - IAN 71494

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info