Bedienungsanleitung Silvercrest SDRB 1000 A1 - IAN 68982 (Seite 45 von 62) (Englisch, Italienisch, Portugiesisch, Spanisch)

679065

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

- 43 -

• Fill the water tank 1 with water (see chapter "Fil-

ling with water").

• Insert the power plug 7 into a correctly installed

and earthed mains power socket.

• Hold the steam brush horizontally.

• Place the temperature regulator 3 at the position

"MAX".

• Heat the steam brush up at the highest setting for

a few minutes. By doing this you will clear produc-

tion residues from the sole 0 of the appliance.

• Activate the steam shot button 8 a few times, so

that steam exits from the soleplate 0.

• Then iron a redundant piece of material, this will

remove any impurites that may possibly be on

the sole of the iron 0.

Note:

On the first heating up of the appliance a small volume

of smoke and smell may be generated, caused by

production residues. This is completely normal and

is not dangerous. Provide for sufficient ventilation,

for example, open a window.

Operation

Note:

• Should the care instructions in the clothing item

forbid ironing (Symbol ), you may not use

the steam brush on it. If you do so, the clothing

item could be permanently damaged.

• Do NOT use the appliance on leather, velvet, im-

pregnated furniture or steam sensitive materials.

If you do, the material/furniture could become

damaged.

Filling with water

Attention!

Fill the watertank 1 exclusively with tap water or distil-

led water mixed with tap water. Never fill watertank 1

with chemical substances, cleaning agents (with the ex-

ception of decalcification agents) or other liquids.

Do not use chemically distilled water. This would

irreparably damage the appliance.

Should the mains water at your locality be rated as

hard, it is recommended that you mix mains water

with some distilled water. Otherwise, the jets for the

steam blast function could calcify (become blocked)

prematurely.

To extend the optimal steam blast function, mix mains

water with distilled water according to the table.

The water hardness level can be queried at your

local water works.

Attention!

Before refilling with water, ALWAYS remove the

plug 7 from the mains power socket! There is a

risk of electric shock!

• Lift the water tank 1 up vertically, in that you slide

the release 4 for the water tank 1 to the rear until

the water tank 1 allows itself to be lifted off. Grasp

the water tank 1 with your thumb and index finger

on the hatched markings to lift it vertically upwards.

The temperature controller 3 remains on the appli-

ance and is not lifted off.

• Open the water fill opening 2 to the water tank 1.

• Using the measuring beaker t, fill the water

tank 1 with mains water to the "Max" marking,

but no further.

Water hardness

Ratios - distilled

water to mains water

very soft / soft 0

medium 1: 1

hard 2: 1

very hard 3: 1

IB_68982_SDRB1000A1_LB5 17.08.2011 11:39 Uhr Seite 43

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Silvercrest SDRB 1000 A1 - IAN 68982 Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Silvercrest SDRB 1000 A1 - IAN 68982

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info