Bedienungsanleitung Silvercrest SDRB 1000 A1 - IAN 68982 (Seite 47 von 62) (Englisch, Italienisch, Portugiesisch, Spanisch)

679065

Zoom out

Zoom in

Vorherige Seite

1/62

Nächste Seite

- 45 -

• Should the heating-up control lamp 5 start to glow

during the process, release the steam blast button 8

and wait a few seconds until the heating-up control

lamp 5 extinguishes.

Note:

Should you press the steam blast button 8 whilst

the heating-up control lamp 5 is glowing the result

will be condensed water instead of steam, and water

will drip from the sole of the iron 0.

• Leave the garment on the clothes hanger to cool

down before putting it on.

Curtain and soft furnishing care

• Creases and wrinkles can be removed from

draperies by hanging them over a pole.

• Then simply follow the directions given under

“Clothing care”.

• Always carry out a test first at a concealed part.

• If you are using the appliance horizontally, every

now and then hold it upright so as to have the

maximum steam performance.

Fluff brush

• Threads, fluff and hairs can be easily removed

with the red fluff brush e by slowly brushing

over the garment with it from left to right.

• You can clean the fluff brush e by brushing with

it in the opposite direction (from right to left)

over, for example, a remnant of material.

Ironing function

• Dismantle the brush attachment w from the

appliance (see “Attaching/detaching the brush

attachment”).

• Connect the appliance to a correctly installed

and earthed mains power socket.

• Adjust the temperature regulator 3 as per the

international point symbols (Care Label) or the

type of material. The heating-up control lamp 5

glows. As soon as the set temperature has been re-

ached, the heating-up control lamp 5 goes out .

Note:

If doubt exists, start with a low temperature and

gradually increase it to a higher one. With sensitive

materials we recommend carrying out an ironing

test at a concealed part (inside seam).

• For heavily creased laundry, you can use the

steam function by pressing the steam shot button

8. To generate the steam, the temperature regu-

lator 3 must be set to at least ••• or higher.

• Should the heating-up control lamp 5 glow during

the process, release the steam blast button 8

and wait for a few moments until the heating-up

control lamp 5 extinguishes.

• You can repeatedly press the steam blast button

8 until the heating-up control lamp 5 glows or

water drips from the sole of the iron 0. Then,

wait until the heating-up control lamp 5 extin-

guishes before activating a further blast of

steam.

Note:

Should you press the steam blast button 8 whilst

the heating-up control lamp 5 is glowing the result

will be condensed water instead of steam, and water

will drip from the sole of the iron 0.

Should the water tank 1 become empty while the

appliance is in use, remove the plug 7 from the

power socket before refilling it.

Washing label Type of material Temperature

regulator 3

Chemical fibres,

e.g. viscose,

polyester

•

(low

temperature)

Silk, Wool

••

(medium

temperature)

Cotton, Linen

•••

(high

temperature)

IB_68982_SDRB1000A1_LB5 17.08.2011 11:39 Uhr Seite 45

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Silvercrest SDRB 1000 A1 - IAN 68982 Seite 47

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Silvercrest SDRB 1000 A1 - IAN 68982

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info