Bedienungsanleitung Skil 0180 (Seite 15 von 164) (Alle Sprachen)

797780

Zoom out

Zoom in

Vorherige Seite

1/164

Nächste Seite

-thoroughly clean the shaft area and the underside of

the tool before mounting the cutting blade

• If the tool should fail despite the care taken in

manufacturing and testing procedures, repair should

be carried out by an after-sales service centre for SKIL

power tools

-send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service

station (addresses as well as the service diagram of the

tool are listed on www.skil.com)

• Be aware that damage due to overload or improper

handling of the tool will be excluded from the warranty

(for the SKIL warranty conditions see www.skil.com or

ask your dealer)

TROUBLESHOOTING

• The following listing shows problem symptoms, possible

causes and corrective actions (if these do not identify

and correct the problem, contact your dealer or service

station)

! 

and ensure that all moving parts have come to a

complete standstill

Tool does not operate

-empty battery -> charge battery

-telescopic handle problem -> fully extend handle and

lock the levers 2a

-hot battery -> let battery cool down

-cutting blades jammed -> clear jammed material

-grass too high -> increase cutting height and tilt tool

-internal fault -> contact dealer/service station

Tool operates intermittently

-internal wiring defective -> contact dealer/service

station

Tool leaves ragged nish or motor labours

-cutting height cut too low -> increase cutting height

-cutting blade blunt -> replace cutting blade

-underside of tool badly clogged -> clean tool

Cutting blade not rotating

-cutting blade obstructed -> clear obstruction

-blade nut/bolt loose -> tighten blade nut/bolt

Tool vibrates abnormally

-cutting blade damaged -> replace cutting blade

-blade nut/bolt loose -> tighten blade nut/bolt

ENVIRONMENT

Only for EU countries

• Do not dispose of electric tools, accessories and

packaging together with household waste material

-in observance of European Directive 2012/19/EC

on waste of electric and electronic equipment and

its implementation in accordance with national law,

electric tools that have reached the end of their life

must be collected separately and returned to an

environmentally compatible recycling facility

-symbol 7 will remind you of this when the need for

disposing occurs

! prior to disposal protect battery terminals with



Only for UK

• Do not dispose of electric tools, accessories and

packaging together with household waste material

-in observance of on Waste Electric and Electronic

Equipment Regulations 2013 (SI 2013/3113), electric

! 

mechanism to the maximum cutting height, then

to a lower cutting height

! adjust your walking pace when mowing long grass

• Mulching function i

-for mulching install mulching plug M as shown

• Battery level indicator e

-press the battery level indicator button N to show the

current battery level ea

! when the lowest level of the battery indicator



eb, the battery is nearly depleted.

• Battery protection

The tool is suddenly being switched o or prevented from

being switched on, when

-the load is too high --> remove load and restart

-the battery is empty --> the 4 levels of the battery

level indicator starts ashing red for 10s; Remove the

battery from the tool and charge the battery ec

-the battery temperature is not within the allowable

 -->4

levels of the battery level indicator keep solid red for

10s; wait until battery has returned within the allowable

operating temperature range ed

! 



damaged

MAINTENANCE / SERVICE

• This tool is not intended for professional use

• Always switch o the tool, remove battery pack, and

ensure that all moving parts have come to a complete

standstill

• Always keep tool clean

• Clean the mower after each use with a hand brush and

a soft cloth

! 

sprays)

-remove compacted grass cuttings from the blade area

with a wooden or plastic implement

• Storage o

-for saving substantial storage space fold the tool

handle and store the tool as illustrated; empty grass



! ensure that the handle cord is not trapped when

folding/unfolding the tool handle (do not drop the

handle)

-do not place other objects on top of the mower when

stored

• Regularly check the grass box for wear or damage

• Regularly check for worn or damaged blades and bolts

and have them replaced in sets to preserve balance

• Replacing the cutting blade p a

! remove battery from tool and remove grass box

J 2c

! wear protective gloves

-turn the mower upside down

-remove/mount the cutting blade with a torque wrench

and two metal rods as aid as illustrated

-the printed blade side towards outside

! only use replacement cutting blades of the correct

type (SKIL spare part number 2610S01593,

marked CH3707037001)

Skil 0180 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info