Bedienungsanleitung Skil 0511 (Seite 8 von 124) (Alle Sprachen)

758619

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

- slide switch F to position 5 (indicator E lights up green)

- if the automatic levelling function is not possible, e.g. because the surface on

which the measuring tool stands deviates by more than 4° from the horizontal

plane, the laser lines ash and indicator E lights up red

- if this is the case, set up the measuring tool in a level position and wait for the

self-levelling to take place

- as soon as the measuring tool is once again within the self-levelling range of

±4°, the laser lines light up continuously and indicator E lights up green

- when not within the self-levelling range of ±4°, working with automatic levelling

is not possible, because it cannot be assured that the laser lines run at a right

angle to each other

- in case of ground vibrations or position changes during operation, the

measuring tool is automatically levelled in again

- to avoid errors, check the position of the horizontal and vertical laser line with

regard to the reference points upon re-levelling

• Working without automatic levelling

- slide switch F in position 6 (indicator E lights up red)

- when automatic levelling is switched o, you can hold the measuring tool freely

in your hand or place it on an inclined surface

- the laser lines no longer necessarily run vertical to each other

• Attaching with the holder

- with holder G you can fasten the measuring tool to dierent objects ranging in

thickness between 10 and 60 mm, such as vertical or horizontal boards or pipes

- loosen fastening screw H, mount the holder to the desired location and tighten

the fastening screw again

- place the measuring tool via tripod mount J onto the 1/4” male thread K of the

holder and screw it on applying moderate force

! do not overtighten the measuring tool, otherwise it can become

damaged

- adjust the holder roughly before switching on the measuring tool; for this, loosen

locking screw L, move the measuring tool until horizontally positioned at the

desired height and retighten the locking screw

APPLICATION ADVICE

• Always use the centre of the laser line for marking (the width of the laser line

changes with the distance)

• Laser viewing glasses 1 (not standard included)

- laser viewing glasses M 1 lter out the ambient light

- this makes the red light of the laser appear brighter for the eyes

- do not use the laser viewing glasses as safety goggles (the laser viewing

glasses are used for improved visualisation of the laser beam, but they do not

protect against laser radiation)

- do not use the laser viewing glasses as sun glasses or in traffic (the laser

viewing glasses do not aord complete UV protection and reduce colour

perception)

• Working with the tripod (not standard included)

- tripod N 1 oers a stable, height-adjustable measuring support

- place the measuring tool via tripod mount J onto the 1/4” male thread of the

tripod and screw the locking screw of the tripod tight

MAINTENANCE / SERVICE

• This tool is not intended for professional use

• Protect the measuring tool against moisture and direct sun light

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 0511 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info