Bedienungsanleitung Skil 0701 (Seite 11 von 112) (Alle Sprachen)

701729

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

• Keep the (extension) cord away from the rotating raking

mechanism

• Always switch o tool and disconnect plug from power

source if the power supply cord or the extension cord is

cut, damaged or entangled (do not touch the cord

before disconnecting the plug)

ACCESSORIES

• SKIL can assure awless functioning of the tool only

when original accessories are used

• The rated speed of the accessory must be at least equal

to the maximum speed marked on the power tool

(accessories running faster than their rated speed

can fly apart)

• Never replace the plastic blades with metallic

blades

BEFORE USE

• Always visually inspect to see that the rotating parts and

raking unit are not worn or damaged

• Have worn or damaged components replaced in sets to

preserve balance

• Only use the tool in daylight or with appropriate articial

lighting

• Check the functioning of the tool before each use and

after any impact; in case of a defect, have it repaired

immediately by a qualied person (never open the tool

yourself)

• Remove any adjusting key or wrench before turning the

power tool on (a wrench or a key left attached to a

rotating part of the power tool may result in

personal injury)

• Before use, thoroughly inspect the working area and

remove any object that the tool may sling during moss

removing (such as stones, loose pieces of wood, etc.)

DURING USE

• Avoid using the tool in bad weather conditions, especially

when there is a risk of lightning

• Keep proper balance and footing at all times; do not

overreach

• Keep proper footing on slopes and do not mow extremely

steep slopes

• Mow across the face of slopes (never up and down)

• Be extremely careful when changing direction on slopes

• Only use the tool in an vertical position, with the raking

unit pointing to the ground (never switch on the tool in

another position)

• Operate the tool at a walking pace only (do not run)

• Do not cross roads or gravel paths with the tool still

running

• Do not get distracted and always concentrate on what

you are doing

• Always ensure that the ventilation openings are kept clear

of debris

AFTER USE

• The raking mechanism continues to rotate for a short

time after the tool is switched o (do not touch the

rotating blades)

• Always switch o tool, disconnect plug from power

source, and ensure that all moving parts have come to a

complete standstill

- whenever leaving the tool unattended

- before clearing jammed material

- before checking, cleaning or working on the tool

- after striking a foreign object

- whenever the tool starts vibrating abnormally

• Before you put down the tool, switch o the motor and

ensure that all moving parts have come to a complete

standstill

• Store the tool indoors in a dry and locked-up place, out

of reach of children

EXPLANATION OF SYMBOLS ON TOOL

3 Warning! Read the instruction manual

4 Double insulation (no earth wire required)

5 Do not dispose of the tool together with household waste

material

6 Wear protective glasses and hearing protection

7 Keep the (extension) cord away from the rotating raking

mechanism

8 Pay attention to the risk of injury caused by flying

debris (keep bystanders a safe distance away from work

area)

9 Beware of sharp blades, keep ngers and toes away /

Disconnect plug before maintenance, adjusting, cleaning,

or if the cord is entangled or damaged / Blades continue

to rotate after the motor is switched o

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

USE

• Assembly instructions 0

! always disconnect the plug before mounting/

removing the raking unit

- slide guard A over motor housing as illustrated until it

clicks into place

! as a safety precaution mount screw B as

illustrated to avoid that guard A comes off when

working

- mount wheel C onto motor housing as illustrated until it

clicks into place

! as a safety precaution mount screw D as

illustrated in 0

- push spindle-lock button E and hold it while you

loosen collet nut F with wrench G

- position raking unit H tight against collet nut F

- tighten collet nut F with wrench G while pushing

spindle-lock button E

! replace the blades when they are worn (SKIL

accessory 2610Z04031)

• Height adjustment !

- loosen locking sleeve J by turning it clockwise

! when using tool for the first time, rotate handle K

90° after loosening locking sleeve J

- extend tube L to the desired height

- tighten locking sleeve J by turning it counter-clockwise

! do not force the tool when extending/retracting

the tube to desired height

• Cord restraint @

- hook the loop in the extension cord over restraint M as

illustrated

- pull tight to secure the extension cord

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 0701 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info