Bedienungsanleitung Skil 0701 (Seite 12 von 112) (Alle Sprachen)

701729

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

• On/o #

- switch on tool by rst pressing safety switch N (which

cannot be locked) and then pulling trigger switch P

- switch o tool by releasing trigger switch P

! after switching off the tool the raking mechanism

continues to rotate for a few seconds

- allow the raking mechanism to stop rotating before

switching on again

! do not rapidly switch on and off

• Before using the tool

- ensure that raking unit H 2 is correctly mounted and

that collet nut F 2 is rmly tightened

- test-run tool for at least 60 seconds at highest no-load

speed in a safe position

- stop immediately in case of considerable vibration or

other defects and check tool to determine the cause

• Removing moss

! ensure that the working area is free of stones,

debris and other foreign objects

- ensure that the bottom side of the tool is kept in a level

position

- start working only when motor is running

- start working near the mains socket and move away

while working

- keep the tool away from solid objects and plants

- do not use the tool in one spot too long

- do not overload the tool

- when you have nished the raking, do not be alarmed

if the lawn looks almost bald

- this is quite normal, as all that remains is good healthy

grass and within 2 to 3 weeks the lawn will have

recovered

• Holding and guiding the tool $

- hold the tool rmly with one hand

- guide the tool at a constant speed over the surface to

be worked on

- maintain a stable working position

- always hold the tool well away from your body

• Replacing blades of lawn raker %

- disconnect plug from power source

- simply remove/mount old/new blade as illustrated

- after replacing the blade test-run the tool for at least

one minute without load to ensure that the tool is

operating properly

! only use replacement blades of the correct type

(SKIL accessory 2610Z04031)

APPLICATION ADVICE

• For best results test-run the tool on a small part of the

surface and check of the lawn does not get damaged

• Regular demossing helps to avoid persistent moss

• For more tips see www.skil.com

MAINTENANCE / SERVICE

• This tool is not intended for professional use

• Keep all nuts, bolts and screws tight to be sure that the

tool is in a safe working condition

• Have worn or damaged parts replaced for safety reasons

• Always switch o tool, disconnect plug from power

source, and ensure that all moving parts have come to a

complete standstill

• Always keep tool and cord clean

! disconnect the plug before cleaning

regularly clean ventilation slots Q 2 with a soft

cloth

- regularly remove dirt from guard A 2 with a soft brush

• Storage ^

- store the tool indoors in a dry and locked-up place,

out of reach of children

- securely mount storage rail R on the wall with 4 screws

(not supplied) and horizontally leveled

• If the tool should fail despite the care taken in

manufacturing and testing procedures, repair should be

carried out by an after-sales service centre for SKIL

power tools

- send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service

station (addresses as well as the service diagram of

the tool are listed on www.skil.com)

TROUBLESHOOTING

• The following listing shows problem symptoms, possible

causes and corrective actions (if these do not identify

and correct the problem, contact your dealer or service

station)

! switch off the tool and disconnect the plug before

investigating the problem

★ Tool does not operate

- power supply socket faulty -> use another socket

- extension cord damaged -> replace extension cord

- raking unit incorrectly mounted -> mount raking unit

again

★ Tool operates intermittently

- internal wiring defective -> contact dealer/service

station

- on/o switch defective -> contact dealer/service

station

★ Moss is not removed completely

- blades damaged/worn -> replace blades

ENVIRONMENT

• Do not dispose of electric tools, accessories and

packaging together with household waste material

(only for EU countries)

- in observance of European Directive 2012/19/EC on

waste of electric and electronic equipment and its

implementation in accordance with national law,

electric tools that have reached the end of their life

must be collected separately and returned to an

environmentally compatible recycling facility

- symbol 5 will remind you of this when the need for

disposing occurs

NOISE/VIBRATION

• Measured in accordance with EN 60335 the sound

pressure level of this tool is 71.4 dB(A) and the sound

power level 91.4 dB(A) (standard deviation: 2,24 dB), and

the vibration 10.3 m/s² (triax vector sum; uncertainty

K = 1.5 m/s²)

• The vibration emission level has been measured in

accordance with a standardised test given in EN 60335; it

may be used to compare one tool with another and as a

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 0701 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info