Bedienungsanleitung Skil 0731 (Seite 13 von 112) (Alle Sprachen)

701723

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

• Inspect the extension cord periodically and replace it, if

damaged (inadequate extension cords can be

dangerous)

• Never use the tool when cord is damaged; have it replaced

by a qualied person

• Never operate the tool with a damaged cutting guard or

without the cutting guard mounted

• Check the functioning of the tool before each use and after

any impact; in case of a defect, have it repaired immediately

by a qualied person (never open the tool yourself)

• Before use, thoroughly inspect the cutting area and remove

any object that the tool may sling during cutting (such as

stones, loose pieces of wood, etc.)

DURING USE

• Avoid using the tool in bad weather conditions, especially

when there is a risk of lightning

• Do not use the tool on wet lawns

• Keep proper balance and footing at all times; do not

overreach

• Keep proper footing on slopes and do not mow extremely

steep slopes

• Operate the tool at a walking pace only (do not run)

• The cutting lines continue to rotate for a short time

after the tool is switched off

• Do not cut grass which is not on the ground (e.g. on walls or

rocks)

• Do not cross roads or gravel paths with the tool still running

• Do not get distracted and always concentrate on what you

are doing

• Always switch o tool, disconnect plug from power source,

and ensure that all moving parts have come to a complete

standstill

- whenever leaving the tool unattended

- before clearing jammed material

- before checking, cleaning or working on the tool

- after striking a foreign object

- whenever the tool starts vibrating abnormally

• Always ensure that the ventilation openings are kept clear of

debris

EXPLANATION OF SYMBOLS ON TOOL

3 Warning! Read the instruction manual

4 Do not expose tool to rain

5 Wear protective glasses and hearing protection

6 Pay attention to the risk of injury caused by flying

debris (keep bystanders a safe distance away from work

area)

7 Immediately disconnect the plug if the (extension) cord is

damaged or cut through while working

8 Double insulation (no earth wire required)

9 Do not dispose of the tool together with household waste

material

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• If for any reason the old plug is cut o the cord of this tool, it

must be disposed of safely and not left unattended

• Do not connect the blue (= neutral) or brown (= live) wire in

the cord of this tool to the earth terminal of the plug

USE

• Assembly instructions 0

- the sequence of the numbers appearing in the drawing

corresponds with the sequence of the steps to be

followed for assembling the tool

- guide handle A 2 can be adjusted by loosening/

tightening knob B 2

! never use the tool without cutting guard C 2

! firmly tighten all screws, bolts and nuts

• Cord restraint !

- hook the loop in the extension cord over restraint D as

illustrated

- pull tight to secure the extension cord

• Height adjustment @

For adjusting the tool height so that your front arm is

straight when trimming

- unlock tube E by pushing button F

- extend tube E to the desired height (3 positions)

• On/o #

- switch on tool by pressing trigger switch G

- switch o tool by releasing trigger switch G

! after switching off the tool the cutting lines

continue to rotate for a few seconds

- allow the cutting lines to stop rotating before switching

on again

! do not rapidly switch on and off

• Trimming

! ensure that the cutting area is free of stones,

debris and other foreign objects

! start trimming only when tool runs at full speed

- start trimming near the mains socket and move away

while working

- cut long grass in layers (always start from the top)

- only trim with the tip of the cutting line

- do not cut damp or wet grass

- prevent the cut grass from clogging the spool (do not

make heavy cuts)

- do not overload the tool

- carefully cut around trees and bushes, so that they do

not come into contact with the cutting lines

- use ower guard H $ to protect vulnerable owers

- keep the tool away from solid objects in order to

protect the cutting lines against excessive wear

- be aware of the kickback forces that occur when solid

objects are touched

• Holding and guiding the tool %

- for cutting long grass slowly swing the tool from right to

left and vice versa

- for cutting shorter grass tilt the tool as illustrated

- for trimming edges turn the cutting head 180° as

illustrated (possible only when lower tube E is

fixed in one of the three height positions)

- hold tool rmly with both hands, so you will have full

control of the tool at all times

- maintain a stable working position

- always hold the tool well away from your body

• Line feeding ^

- two cutting lines will be released and cut o to the

correct length by line cutting blade J each time the tool

is switched on

! take care against injury from line cutting blade J

- after line feeding always return the tool to its normal

operating position before switching on

- feed the lines regularly to maintain full cutting circle

- when the motor runs without load and no grass is cut,

the cutting lines are worn or broken; rewind the spool

or replace the spool system

Skil 0731 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info