Bedienungsanleitung Skil 0731 (Seite 14 von 112) (Alle Sprachen)

701723

Zoom out

Zoom in

Vorherige Seite

1/112

Nächste Seite

• Rewinding spool &

In case the cutting lines fail to protrude from spool cap K

! switch off the tool and disconnect the plug

- remove spool system from tool and take out spool from

spool cap K

- tightly rewind both cutting lines evenly in layers in

arrow direction

- insert both lines into spool slots X and ensure that they

are securely in place (leave sucient length of line)

- thread both lines through spool holes Y before placing

the rewound spool into spool cap K

! ensure that the spool is located securely in place,

then release both lines from slots X by pulling

them firmly

- mount spool system onto tool (turn spool clockwise

until it clicks into place) *

• Replacing spool *

! switch off the tool and disconnect the plug

- simply remove/mount old/new spool as illustrated

- after replacing the spool test-run the tool for at least

one minute without load to ensure that the tool is

operating properly

! be sure tool is switched off when plugging in

MAINTENANCE / SERVICE

• This tool is not intended for professional use

• Always switch o tool, disconnect plug from power

source, and ensure that all moving parts have come to a

complete standstill

• Always keep tool and cord clean (especially the

ventilation slots)

- clean the tool with a damp cloth (do not use cleaning

agents or solvents)

- clean line cutting blade J 2 and cutting guard C 2

after each use

- clean ventilation slots L 2 regularly with a brush or

compressed air

• Regularly check the condition of the cutting head and the

tightness of nuts, bolts and screws

• Regularly check for worn or damaged components and

have them repaired/replaced when necessary

• Storage (

- store the tool indoors in a dry and locked-up place,

out of reach of children

- securely mount storage rail M on the wall with 4

screws (not supplied) and horizontally leveled

• If the tool should fail despite the care taken in

manufacturing and testing procedures, repair should be

carried out by an after-sales service centre for SKIL

power tools

- send the tool undismantled together with proof of

purchase to your dealer or the nearest SKIL service

station (addresses as well as the service diagram of

the tool are listed on www.skil.com)

TROUBLESHOOTING

• The following listing shows problem symptoms, possible

causes and corrective actions (if these do not identify

and correct the problem, contact your dealer or service

station)

! switch off the tool and disconnect the plug before

investigating the problem

★ Tool does not operate

- power supply socket faulty -> use another socket

- extension cord damaged -> replace extension cord

★ Tool operates intermittently

- internal wiring defective -> contact dealer/service

station

- on/o switch defective -> contact dealer/service

station

★ Tool vibrates abnormally

- grass too high -> cut in stages

★ Tool does not cut

- line too short/broken o -> feed the line by switching

tool o and on again

★ Line cannot be fed

- spool empty -> replace spool

- line entangled inside spool -> inspect spool; rewind if

necessary

★ Line keeps breaking

- line entangled inside spool -> inspect spool; rewind if

necessary

- trimmer incorrectly used -> only trim with the tip of the

line; avoid stones, walls and other hard objects; feed

the line regularly

ENVIRONMENT

• Do not dispose of electric tools, accessories and

packaging together with household waste material

(only for EU countries)

- in observance of European Directive 2012/19/EC on

waste of electric and electronic equipment and its

implementation in accordance with national law,

electric tools that have reached the end of their life

must be collected separately and returned to an

environmentally compatible recycling facility

- symbol 9 will remind you of this when the need for

disposing occurs

NOISE / VIBRATION

• Measured in accordance with EN 60335 the sound

pressure level of this tool is 84 dB(A) and the sound

power level 95 dB(A) (standard deviation: 1 dB), and the

vibration 2.9 m/s² (triax vector sum; uncertainty K = 1.5

m/s²)

• The vibration emission level has been measured in

accordance with a standardised test given in EN 60335; it

may be used to compare one tool with another and as a

preliminary assessment of exposure to vibration when

using the tool for the applications mentioned

- using the tool for dierent applications, or with dierent

or poorly maintained accessories, may signicantly

increase the exposure level

- the times when the tool is switched o or when it is

running but not actually doing the job, may signicantly

reduce the exposure level

! protect yourself against the effects of vibration

by maintaining the tool and its accessories,

keeping your hands warm, and organizing your

work patterns

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 0731 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info