Bedienungsanleitung Skil 0738 (Seite 9 von 296) (Alle Sprachen)

591167

Zoom out

Zoom in

Vorherige Seite

1/296

Nächste Seite

 Store tool/charger/battery in locations where

temperature will not exceed 40°C or drop below 0°C

 Do not use charger when damaged; take it to one of the

ocially registered SKIL Service Stations for a safety

check

 Do not use charger when cord or plug is damaged; cord

or plug should be replaced immediately at one of the

ocially registered SKIL Service Stations

 Do not use battery when damaged; it should be

replaced immediately

 Do not disassemble charger or battery

 Do not attempt to recharge non-rechargeable batteries

with the charger

EXPLANATION OF SYMBOLS ON TOOL/CHARGER/

BATTERY

③ Warning! Read the instruction manual

④ Do not expose tool/charger/battery to rain

⑤ Wear protective glasses and hearing protection

⑥ 

debris (keep bystanders a safe distance away from

work area)

⑦ Only use the charger indoors

⑧ Double insulation (no earth wire required)

⑨ Batteries may explode when disposed of in re, so do

not burn battery for any reason

⑩ Store tool/charger/battery in locations where

temperature will not exceed 50°C

⑪ Do not dispose of the charger together with household

waste material

⑫ Do not dispose of the battery together with household

waste material

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

 If for any reason the old plug is cut o the cord of the

charger, it must be disposed of safely and not left

unattended

 Do not connect the blue (= neutral) or brown (= live) wire

in the cord of the charger to the earth terminal of the

plug

USE

 Always remove battery from tool before making any

adjustment or changing any accessory, in order to

reduce the risk of starting the tool accidentally

 Assembly instructions ⑬

- the sequence of the numbers appearing in the drawing

corresponds with the sequence of the steps to be

followed for assembling the tool

- mount cutting guard A as illustrated with round head

screw supplied

! 

! never use the tool without cutting guard A

 Adjusting guide handle ⑭

- loosen/tighten handle B ② by turning it

counter-clockwise/clockwise

 Height adjustment ⑮

For adjusting the tool height so that your front arm is

straight when trimming

- loosen locking sleeve C by turning it clockwise

- extend tube D to the desired height

- tighten locking sleeve C by turning it counter-clockwise

 Charging battery ⑯

- battery of new tools is not fully charged

- connect charger E to power source as illustrated ⑯a

- green light F will turn on indicating that the charger is

ready for operation ⑯a

- insert battery G into charger as illustrated ⑯b

- green light F will blink indicating that the battery is

being charged ⑯b

- after approximately 1 hour the battery is fully charged

and green light F stays on after blinking ⑯c

IMPORTANT:

- if green light F does not blink after inserting a battery,

this may mean:

1) that the battery is too cold or too hot (charger only

charges batteries when its temperature is between

0°C and 45°C)

2) that the battery should be replaced

- the lithium-ion battery can be charged at any time

(interrupting the charging procedure does not damage

the battery)

- the lithium-ion battery does not have to be empty

before charging (no "memory-eect" as with nickel-

cadmium batteries)

- while charging, the charger and the battery may

become warm to touch; this is normal and does not

indicate a problem

- ensure that the outside surface of the battery is clean

and dry before inserting into charger

- do not remove battery from tool while it is running

- a signicantly reduced working period after charging

indicates that the battery is worn out and should be

replaced

 Battery protection

Switches o the tool automatically when

1) the load is too high

2) the battery temperature is not within the allowable

operating temperature range of -10 to +50°C

3) the lithium-ion battery is nearly empty (to protect

against deep discharge)

! 



be damaged

 On/o ⑰

- switch on/o the tool by pulling/releasing trigger H

! 

rotate for a few seconds

- allow the cutting blade to stop rotating before

switching on again

! 

 Trimming

! ensure that the cutting area is free of stones,

debris and other foreign objects

! start trimming only when tool runs at full speed

- cut long grass in layers (always start from the top)

- only trim with the tip of the cutting blade

- do not cut damp or wet grass

- prevent the cut grass from clogging the blade (do not

make heavy cuts)

- do not overload the tool

- carefully cut around trees and bushes, so that they do

not come into contact with the cutting blade

- use ower guard J ⑱ to protect vulnerable owers

- keep the tool away from solid objects in order to

protect the cutting blade against excessive wear

- be aware of the kickback forces that occur when solid

objects are touched

Skil 0738 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info