Bedienungsanleitung Skil 0738 (Seite 10 von 296) (Alle Sprachen)

591167

Zoom out

Zoom in

Vorherige Seite

1/296

Nächste Seite

 Holding and guiding the tool ⑲

- for cutting long grass slowly swing the tool from right to

left and vice versa

- for cutting shorter grass tilt the tool as illustrated

- turn the tool 180° for trimming edges

- hold tool rmly with both hands, so you will have full

control of the tool at all times

- maintain a stable working position

- always hold the tool well away from your body

 Replacing cutting blade ⑳

! remove battery from tool

- simply remove/mount old/new cutting blade as

illustrated

- after replacing the cutting blade test-run the tool for at

least one minute without load to ensure that the tool is

operating properly

- extend the service life of the cutting blade twice by

removing it, turning it 180°, and mounting it again

 Blade storage compartment ㉑

MAINTENANCE / SERVICE

 This tool is not intended for professional use

 Opening the housing shell can damage or destroy

the tool

 Keep tool, charger and cutting blades clean

! unplug charger from power source before

cleaning

! always remove the battery before cleaning

- clean cutting blade L ② and cutting guard A ② after

each use

- clean the tool with a damp cloth (do not use cleaning

agents or solvents)

- clean ventilation slots M ② regularly with a brush or

compressed air

 Regularly check the condition of the cutting head and

the tightness of nuts, bolts and screws

 Regularly check for worn or damaged components and

have them repaired/replaced when necessary

 Storage

- store the tool indoors in a dry and locked-up place,

out of reach of children

- securely mount storage rail N on the wall with 4 screws

(not supplied) and horizontally leveled

 If the tool/charger should fail despite the care taken in

manufacturing and testing procedures, repair should

be carried out by an after-sales service centre for SKIL

power tools

- send the tool or charger undismantled together with

proof of purchase to your dealer or the nearest SKIL

service station (addresses as well as the service

diagram of the tool are listed on www.skil.com)

- in case of a defective charger send both charger and

battery to your dealer or the SKIL service station

TROUBLESHOOTING

 The following listing shows problem symptoms, possible

causes and corrective actions (if these do not identify

and correct the problem, contact your dealer or service

station)

! 

investigating the problem

 Tool operates intermittently

- internal wiring defective -> contact dealer/service

station

- on/o switch defective -> contact dealer/service

station

 Tool vibrates abnormally

- grass too high -> cut in stages

 Tool does not cut

- cutting blade broken o -> replace cutting blade

ENVIRONMENT

 Do not dispose of electric tools, batteries,

accessories and packaging together with

household waste material (only for EU countries)

- in observance of European Directive 2012/19/EC

on waste of electric and electronic equipment and

its implementation in accordance with national law,

electric tools that have reached the end of their life

must be collected separately and returned to an

environmentally compatible recycling facility

- symbol ⑪ will remind you of this when the need for

disposing occurs

! remove the battery before disposal of the tool

 The battery must be kept separate from the natural

environment and should not be disposed of as normal

domestic waste (symbol ⑫ will remind you of this when

the need for disposing occurs)

! prior to disposal protect battery terminals with



- dispose of the battery at an ocial collection point for

batteries

! 

so do not burn battery for any reason

DECLARATION OF CONFORMITY

 We declare under our sole responsibility that this

product is in conformity with the following standards

or standardized documents: EN 60335, EN 61000,

EN 55014 in accordance with the provisions of the

directives 2006/95/EC, 2004/108/EC, 2006/42/EC,

2000/14/EC, 2011/65/EU

 : SKIL Europe BV (PT-SEU/ENG1),

4825 BD Breda, NL

11.04.2014

SKIL Europe BV, 4825 BD Breda, NL

Marijn van der Hoofden

Operations & Engineering

Olaf Dijkgraaf

Approvals Manager

NOISE/VIBRATION

 Measured in accordance with EN 60335 the sound

pressure level of this tool is <70 dB(A) (standard

deviation: 3 dB) and the vibration 1 m/s² (hand-arm

method; uncertainty K = 1.5 m/s²)

 Measured in accordance with 2000/14/EC the

guaranteed sound power level LWA is lower than 86

dB(A) (conformity assessment procedure according to

Annex VI)

Notied body : INTERTEK

Notied body identication number : 0359

 The vibration emission level has been measured in

accordance with a standardised test given in EN 60335;

it may be used to compare one tool with another and as

Skil 0738 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info