Bedienungsanleitung Skil 0770 (Seite 8 von 96) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

480089

Zoom out

Zoom in

Vorherige Seite

1/96

Nächste Seite

• Only operate the tool in open space (not too close to a

wall or other solid objects) and on a rm, level surface

• Store the tool indoors in a dry and locked-up place, out

of reach of children

BEFORE USE

• Check that all screws, nuts, bolts and other fasteners are

properly secured and that guards and screens are in place

• Ensure that the feed intake is empty

DURING USE

• Keep your face and body away from the feed

intake opening

• Do not allow hands (or any other part of the body) or

clothing inside the feed intake opening, outlet opening or

near any moving part

• Keep proper balance and footing at all times; do

not overreach

• Never stand at a higher level than the base of the tool

when feeding material

• Always keep proper distance from the outlet zone when

operating the tool

• When feeding material into the tool be extremely careful

that pieces of metal, rocks, bottles, cans or other foreign

objects are not included

• If the cutting mechanism strikes any foreign object or if

the tool should start making any unusual noise or

vibration, immediately switch o, allow the cutting blade

to stop, disconnect the plug and take the following steps

- inspect for damage

- replace or repair any damaged parts

- check for and tighten any loose parts

• Do not allow processed material to build up in the outlet

zone; this may prevent proper discharge which can result

in kickback of material through the feed intake opening

• If the tool becomes clogged, switch o, allow the cutting

blade to stop and disconnect the plug before

clearing debris

• Keep the motor cooling vents clean of debris and other

accumulations to prevent damage to the motor or

possible re

• Do not tilt or transport the tool while the motor is running

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

USE

• Assembly instructions $

- mount wheels with the two wrenches A supplied and

assemble tool as illustrated

- position collection bag B underneath outlet C

- mount prodder holder D

• On/o %

- switch on/o the tool by pushing switch E in

“I”/”O” position

! after switching off the tool the blade continues to

rotate for a few seconds

- allow the cutting blade to stop rotating before

switching on again

! the tool will not start unless securing knob F is

fully tightened

! do not rapidly switch on and off

• Restart protection

- after a power supply failure the tool will not restart on

its own

- use switch E % for restarting the tool

• Overload protection

Overloading (e.g. blocking up the cutting blade) can lead

to a standstill of the tool

- wait a short period before switching on the tool again

- restart tool by rst pushing button G % and then

switch E %

• Shredding ^

- feed the material to be chopped through feed intake

opening H

- only insert as much material so that the feed intake will

not be blocked up

! longer material could lash out when being cut

! small pieces of shredded material may be ejected

from the feed intake opening

! wear safety glasses, hearing protection and

protective gloves when using the tool

- do not ll soft waste such as kitchen rubbish into

the shredder

- ensure that the chopped material can fall freely from

outlet C

- ensure that ventilation slots J 2 will not be covered by

the collection bag or the chopped material

- avoid blocking outlet C with shredded material as this

could result in kickback of material through feed intake

opening H

• Removing blockage &

! switch off the tool and disconnect the plug

- loosen securing knob F and open the tool as illustrated

- clean the blade area (remove compacted debris with a

woorden or plastic implement)

- also clean outlet C of any debris

- close the tool and tighten securing knob F rmly

• Reversing/changing cutting blade *

! switch off the tool and disconnect the plug

- the cutting blade has a cutting edge on both sides; so

if one side has become blunt, the other side can

be used

- replace the cutting blade when both sides are blunt

(SKIL spare part number 2610Z02553,

marked YAT 8231-545201)

- loosen securing knob F and open the tool as illustrated

- loosen both blade bolts with hex key L while using

metal plate M as support

- reverse and mount the cutting blade as illustrated

- tighten both blade bolts with hex key L while using

metal plate M as support

- close the tool and tighten securing knob F rmly

APPLICATION ADVICE

• For best results shred fresh branches soon after they

have been cut

• Use prodder K for feeding soft material (

• Shred soft garden waste in smaller loads, particularly

when wet

• Blockages can be avoid by intermittently

shredding branches

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 0770 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info