Bedienungsanleitung Skil 1415 AC (Seite 8 von 172) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

482561

Zoom out

Zoom in

Vorherige Seite

1/172

Nächste Seite

e) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and any

other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired

before use. Many accidents are caused by poorly

maintained power tools

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control

g) Use the power tool, accessories and tool bits etc., in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations dierent

from those intended could result in a hazardous situation

5) SERVICE

a) Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained

SAFETY INSTRUCTIONS FOR HIGH-SPEED

ROTATION TOOLS

1) SAFETY INSTRUCTIONS FOR ALL OPERATIONS

a) This power tool is intended to function as a grinder,

sander, wire brush, polisher, carving or cut-off tool.

Read all safety warnings, instructions, illustrations

and specifications provided with this power tool.

Failure to follow all instructions listed below may result in

electric shock, re and/or serious injury.

b) Do not use accessories which are not specifically

designed and recommended by the tool

manufacturer. Just because the accessory can be

attached to your power tool, it does not assure safe

operation.

c) The rated speed of the accessory must be at least

equal to the maximum speed marked on the power

tool. Accessories running faster than their rated speed

can y apart.

d) The outside diameter and the thickness of your

accessory must be within the capacity rating of your

power tool. Incorrectly sized accessories cannot be

adequately controlled.

e) The arbour size of wheels, sanding drum or any

other accessory must properly fit the spindle or

collet of the power tool. Accessories that do not match

the mounting hardware of the power tool will run out of

balance, vibrate excessively and may cause loss of

control.

f) Mandrel mounted wheels, sanding drums, cutters or

other accessories must be fully inserted into the

collet or chuck. The “overhang” or the length of the

mandrel from the wheel to the collet must be

minimal. If the mandrel is insuciently held and/or the

overhang of the wheel is too long, the mounted wheel

may become loose and ejected at high velocity.

g) Do not use a damaged accessory. Before each use

inspect the accessory such as abrasive wheels for

chips and cracks, sanding drum for cracks, tear or

excess wear, wire brushes for loose or cracked

wires. If the power tool or accessory is dropped,

inspect for damage or install an undamaged

accessory. After inspecting and installing an

accessory, position yourself and bystanders away

from the plane of the rotating accessory and run the

power tool at maximum no load speed for one

minute. Damaged accessories will normally break apart

during this test time.

h) Wear personal protective equipment 4. Depending

on application, use face shield, safety goggles or

safety glasses. As appropriate, wear dust mask,

hearing protectors, gloves and shop apron capable

of stopping small abrasive or workpiece fragments.

The eye protection must be capable of stopping ying

debris generated by various operations. The dust mask or

respirator must be capable of ltrating particles

generated by your operation. Prolonged exposure to high

intensity noise may cause hearing loss.

i) Keep bystanders a safe distance away from work

area. Anyone entering the work area must wear

personal protective equipment. Fragments of the

workpiece or of a broken accessory may y away and

cause injury beyond the immediate area of operation.

j) Hold power tool by insulated gripping surfaces only,

when performing an operation where the cutting

accessory may contact hidden wiring or its own

cord. A cutting accessory contacting a “live” wire may

make exposed metal parts of the power tool “live” and

could give the operator an electric shock.

k) Always hold the tool firmly in your hands during the

start-up. The reaction torque of the motor, as it

accelerates to full speed, can cause the tool to twist.

l) Use clamps to support workpiece whenever

practical. Never hold a small workpiece in one hand

and the tool in the other hand while in use. Clamping

a small workpiece allows you to use both hands to control

the tool. Round material such as dowel rods, pipes or

tubing have a tendency to roll while being cut, and may

cause the bit to bind or jump toward you.

m) Position the cord clear of the spinning accessory. If

you lose control, the cord may be cut or snagged and

your hand or arm may be pulled into the spinning

accessory.

n) Never lay the power tool down until the accessory

has come to a complete stop. The spinning accessory

may grab the surface and pull the power tool out of your

control.

o) After changing the bits or making any adjustments,

make sure the collet nut, chuck or any other

adjustment devices are securely tightened. Loose

adjustment devices can unexpectedly shift, causing loss

of control, loose rotating components will be violently

thrown.

p) Do not run the power tool while carrying it at your

side. Accidental contact with the spinning accessory

could snag your clothing, pulling the accessory into

your body.

q) Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the housing and

excessive accumulation of powdered metal may cause

electrical hazards.

r) Do not operate the power tool near flammable

materials. Sparks could ignite these materials.

s) Do not use accessories that require liquid coolants.

Using water or other liquid coolants may result in

electrocution or shock.

Skil 1415 AC Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info