Bedienungsanleitung Skil 1415 AC (Seite 10 von 172) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

482561

Zoom out

Zoom in

Vorherige Seite

1/172

Nächste Seite

• Never use grinding discs over 32 mm (1 1/4”) Ø

• Never use drill bits over 3.2 mm (1/8”) Ø

• Never use a cutting disc for side grinding

• Never use reducors or adaptors to t large-hole grinding/

cutting discs

BEFORE USE

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool (tools with

a rating of 230V or 240V can also be connected to a

220V supply)

• Do not work materials containing asbestos (asbestos

is considered carcinogenic)

• Secure the workpiece (a workpiece clamped with clamping

devices or in a vice is held more securely than by hand)

• Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

• Wear protective glasses and hearing protection 4,

protective gloves and sturdy shoes; when necessary, also

wear an apron

• Dust from material such as paint containing lead, some

wood species, minerals and metal may be harmful (contact

with or inhalation of the dust may cause allergic reactions

and/or respiratory diseases to the operator or bystanders);

wear a dust mask and work with a dust extraction

device when connectable

• Certain kinds of dust are classied as carcinogenic (such

as oak and beech dust) especially in conjunction with

additives for wood conditioning; wear a dust mask and

work with a dust extraction device when connectable

• Follow the dust-related national requirements for the

materials you want to work with

• Ensure that the collet size corresponds with the shaft size

of the accessory

• Be sure tool is switched o when plugging in

DURING USE

• Use auxiliary handle(s), if supplied with the tool

(loss of control can cause personal injury)

• Hold power tool by insulated gripping surfaces,

when performing an operation where the cutting

accessory may contact hidden wiring or its own

cord (a cutting accessory contacting a “live” wire may

make exposed metal parts of the power tool “live” and

could give the operator an electric shock)

• Always keep the cord away from moving parts of the tool;

direct the cord to the rear, away from the tool

• Never use the tool when cord is damaged; have it

replaced by a qualied person

• Never use spindle lock while tool is running (damage

due to improper handling will be excluded from the

guarantee)

• Keep hands away from rotating accessories

• When grinding metal, sparks are generated; keep other

persons and combustible material from work area

• Keep the ventilation slots uncovered while working

• In case of electrical or mechanical malfunction,

immediately switch o the tool and disconnect the plug

AFTER USE

• The accessory continues to rotate for a short time after

the tool has been switched o

• Before you put down the tool, switch o the motor and

ensure that all moving parts have come to a complete

standstill

• After switching o the tool, never stop the rotation of the

accessory by a force applied against it

• Store tool in locations where temperature will not

exceed 50°C

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

• If for any reason the old plug is cut o the cord of this tool, it

must be disposed of safely and not left unattended

USE

• Changing accessories 5

! switch off the tool and disconnect the plug

! ensure that collet size corresponds with shaft

size of accessory

- push spindle-lock button B and hold it while you turn

collet nut D by hand until the spindle lock prevents

further rotation and loosen collet nut D with wrench E

- insert an accessory in collet C as far as possible to

minimize run-out and unbalance

- push spindle-lock button B and hold it while you

tighten collet nut D with wrench E

! avoid excessive tightening of collet nut D

! never tighten collet nut, if there is no accessory

in collet; collet may be damaged

• Changing collets 6

! switch off the tool and disconnect the plug

- push spindle-lock button B and hold it while you

remove collet nut D

- remove collet C

- insert new collet

! never tighten collet nut, if there is no accessory

in collet; collet may be damaged

• Before using the tool

- ensure that accessory is correctly mounted and rmly

tightened

- check if accessory runs freely by turning it by hand

- test-run tool for at least 30 seconds at highest no-load

speed in a safe position

- stop immediately in case of considerable vibration or

other defects and check tool to determine the cause

• On/o switch 7

- switch on/o the tool by pushing knob A in “I”/”O”

position

! before the accessory reaches the workpiece, the

tool should run at full speed

! before switching off the tool, you should lift it

from the workpiece

• Speed control 8

For optimal results on dierent materials

- select speed with wheel G (also while tool is running)

- use table 9 as reference for determining the right

speed

- before starting a job, nd the optimal speed by testing

out on spare material

! after longer periods of working at low speed,

allow the tool to cool down by running it for

approximately 3 minutes at high speed with

no load

Skil 1415 AC Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info