Bedienungsanleitung Skil 1928 (Seite 7 von 108) (Alle Sprachen)

758614

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

-with the laser beam activated, aim

the laser at the target

-this mode can be used to move the

tool relative to the target and the

continuously updated distance is

displayed

-when the display shows only

dashes, the measurement cannot

be made (see APPLICATION

ADVICE for possible causes) 9

-press the main button H to stop the

measurement and save the current

value q

! keep in mind that the tool

measures from its rear (the

tool length is included in the

measuring result)

-press main button H to activate

laser and start a consecutive

measurement; press main

button H again to stop and

save the measurement (up to 2

measurements can be displayed)

• Wheel measuring mode (1929) w

-press the side button to enter wheel

measuring mode (see blinking

wheel indicator)

-use wheel to measure (see rotating

wheel indicator)

-the wheel can be used forwards and

backwards

-when changing direction during

measurement, the measured value

will be deducted and even be

negative if you cross the starting

point again

! try to hold the tool in a

consistent angle and keep a

steady pressure to get to most

accurate measurement

-press side button G quickly twice to

restart the measurement e

-press main button H to stop the

measurement (see wheel indicator)

and save the measurement

-press main button H to start a

consecutive measurement; press

main button H again to stop and

save the measurement (up to 2

measurements can be displayed)

-press side button G again to return

to laser measurement mode

• Area measurement r

-press main button H quickly twice

to calculate and show the area from

the last 2 measurements

be created in the measuring tool which

may ignite the dust or fumes)

EXPLANATION OF SYMBOLS ON

TOOL

2 Read the instruction manual before

use

3 Do not dispose of electric tools and

batteries together with household

waste material

4 Laser radiation / Do not stare into

beam / Class 2 laser product

USE

• Inserting/replacing the batteries 5

-alkali-manganese batteries are

recommended for the measuring

tool

-do not use rechargeable batteries

-to open the battery lid D, press on

the latch E and fold the battery lid up

-insert 2 x AAA batteries (pay

attention to correct polarisation)

-always replace all batteries at the

same time

-only use batteries from one brand

and with the identical capacity

-close battery lid D

-remove the batteries from the

measuring tool when not using

it for extended periods (when

storing for extended periods,

the batteries can corrode and

self-discharge)

• Battery level indicator 6

-during use the battery level indicator

on the display indicates the

remaining battery capacity

• On/o

-press side button G to turn on the

tool

-press and hold side button G for 1

second to turn o the tool

• Change units 8

-press and hold main button H for 1

second to change the measurement

unit (feet, feet/inch, or meter)

• Laser measuring mode

-when you turn on the tool, it will

enter laser measuring mode with the

laser turned o (see indicator) 7a

-press main button H to turn on the

laser (see blinking laser indicator)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 1928 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info