Bedienungsanleitung Skil 1928 (Seite 8 von 108) (Alle Sprachen)

758614

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

• Keep the measuring tool clean at all

times

• Do not immerse the measuring tool in

water or other uids

• Wipe o debris using a moist and

soft cloth

• Do not use any cleaning agents or

solvents

• Regularly clean the surfaces at the exit

opening of the laser in particular, and

pay attention to any u of bres

• If the tool should fail despite the care

taken in manufacturing and testing

procedures, repair should be carried

out by an after-sales service centre for

SKIL power tools

-send the tool undismantled

together with proof of purchase to

your dealer or the nearest SKIL

service station (addresses as well

as the service diagram of the tool

are listed on www.skil.com)

• Be aware that damage due to overload

or improper handling of the tool will

be excluded from the warranty (for

the SKIL warranty conditions see

www.skil.com or ask your dealer)

ENVIRONMENT

• Do not dispose of electric

tools, batteries, accessories

and packaging together with

household waste material (only for

EU countries)

-in observance of European Directive

2012/19/EC on waste of electric

and electronic equipment and its

implementation in accordance with

national law, electric tools that have

reached the end of their life must be

collected separately and returned

to an environmentally compatible

recycling facility

-symbol 4 will remind you of this

when the need for disposing occurs

Mesure du laser 1928/1929

INTRODUCTION

• Cet outil permet de mesurer des

distances tant à l'intérieur qu'à

-when there is only 1 measurement,

the display will show only dashes

-when pressing main button

H again you will return to the

measuring mode, showing the last 2

measurements in the display

APPLICATION ADVICE

• Faulty measurements cannot be

excluded when measuring to dierent

surfaces; the problematic surfaces are:

-transparent surfaces (e.g., glass,

water)

-reective surfaces (e.g., polished

metal, glass)

-porous surface (e.g., insulation

materials)

-structured surfaces (e.g., roughcast,

natural stone)

If required, use piece of paper or a

laser target plate (not included) on

these surfaces

• Other possible causes for faulty

measurement:

-the measurement took place outside

the measuring range

-the angle between laser beam and

target was too small

-the reception lens B or the laser

beam opening A was misted up (e.g.

due to a rapid temperature change)

• Air layers with varying temperatures

or indirectly received reections can

aect the measured value

MAINTENANCE / SERVICE

• This tool is not intended for

professional use

• Protect the measuring tool against

moisture and direct sun light

• Do not subject the measuring

tool to extreme temperatures or

variations in temperature (the

accuracy of the measuring tool can

be impaired)

-as an example, do not leave it in

vehicles for long time

-allow the measuring tool to adjust

to the ambient temperature before

putting it into operation

• Avoid heavy impact to or falling down

of the measuring tool

-damage to the measuring tool can

impair its accuracy

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 1928 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info