Bedienungsanleitung Skil 2900 (Seite 7 von 124) (Alle Sprachen)

519345

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

- switch o the tool/unlock the switch by pressing switch

A at the back

• Charging battery #

- battery of new tools is not fully charged

- plug charger J into wall socket

- insert charger plug K into battery as illustrated

- charging light H turns on indicating that the battery is

being charged

- after 3 hours the charging operation will be completed,

and the battery may be used

IMPORTANT:

- do not charge at temperatures below 0°C and over

40°C; this will seriously damage the battery as well as

the charger

- while charging, the charger and the battery may

become warm to touch; this is normal and does not

indicate a problem

- do not remove battery from tool while it is running

! a battery that is new or has not been used for a

longer period does not develop its full capacity

until after approximately 5 charging/discharging

cycles

- do not repeatedly recharge the battery after only a few

minutes of operation; this may result in a reduction of

operating time and battery eciency

- the battery must be kept separate from the natural

environment and should not be disposed of as normal

domestic waste (symbol 0 will remind you of this

when the need for disposing occurs)

! prior to disposal protect battery terminals with

heavy tape to prevent short-circuit

- if you anticipate long periods of non-use for the tool, it

is best to unplug the charger from its power source

• Changing batteries $

- press button G and slide o battery

- mount battery by sliding it onto tool until it snap-locks

• Changing scissor heads %

! remove battery from tool

- lift button B and hold it while sliding o scissor head

- mount scissor head by sliding it onto tool as illustrated

until it snap-locks

• Operating the tool

- before using the tool, unplug the charger and

disconnect the tool from the charger

- remove blade protection cap L 2

- switch on the tool

- let the cutting blades run freely for a few seconds

before starting the cut

- do not apply too much pressure on the tool; let the tool

do the work for you

- both straight and curved cuts can be made in an

accurate manner

! the cutting blades become hot during use; do not

touch them before they have cooled down

• Cutting materials ^

- use scissor head C 2 for cutting soft and exible

materials such as paper, curtains, carpet, leather,

wallpaper, vinyl, foil, etc.

- scissor head C carries symbol D 2 to indicate soft

and exible materials

- cutting tough materials (such as hard plastics and tin

sheets) with scissor head C 2 will sooner blunt the

blades; we therefore advise to use scissor head E 2

(available as part of SKIL accessory 2610397158) for

cutting tough materials

- observe the following maximum material thicknesses

in order to prevent damaging the blades:

WHEN USING SCISSOR HEAD FOR SOFT

MATERIALS:

cotton fabrics 3 mm

felt 6 mm

leather 4 mm

carpet (backing) 4 mm

vinyl oor-covering 4 mm

corrugated cardboard 6 mm

solid cardboard 2 mm

rose stems 4 mm

WHEN USING SCISSOR HEAD FOR TOUGH

MATERIALS:

vinyl oor-covering 4 mm

corrugated cardboard 6 mm

solid cardboard 2 mm

plastic straps 1.8 mm

plastic sheets (PVC, etc.) 1.25 mm

tin/aluminium sheets 0.4 mm

! do not cut metals other than tin/aluminium

sheets

- always test out rst on a piece of scrap material

! do not attempt to sharpen the cutting blade

surfaces; replace the scissor head when the

cutting blades are worn or damaged

APPLICATION ADVICE

• For working continuously you may use an additional

interchangeable battery (available as SKIL accessory

2610397159) enabling you to charge one battery while

using the other

• For more tips see www.skil.com

MAINTENANCE / SERVICE

• This tool is not intended for professional use

• Keep tool and charger clean

! always remove the battery before cleaning

- do not immerse tool, charger or scissor head in water

- clean tool, charger and scissor head with a damp cloth

(do not use any abrasive or solvent-based cleaners)

- keep slot M & in scissor head connection free of dust

and dirt with a soft brush or dry cloth

- cover cutting blades with protection cap L 2 when

storing the tool

! unplug charger from power source before

cleaning

• If the tool/charger should fail despite the care taken in

manufacturing and testing procedures, repair should be

carried out by an after-sales service centre for SKIL

power tools

- send the tool or charger undismantled together with

proof of purchase to your dealer or the nearest SKIL

service station (addresses as well as the service

diagram of the tool are listed on www.skil.com)

- in case of a defective charger send both charger and

battery to your dealer or the SKIL service station

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 2900 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Skil 2900

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info