Bedienungsanleitung Skil 3930 (Seite 12 von 196) (Alle Sprachen)

758609

Zoom out

Zoom in

Vorherige Seite

1/196

Nächste Seite

• Secure the workpiece (a workpiece clamped with

clamping devices or in a vice is held more securely than

by hand)

• Do not clamp the tool in a vice

DURING USE

• In case of electrical or mechanical malfunction,

immediately switch o the tool and remove battery

• In case of a battery protection cut o, or when the

battery is removed, the tool will not restart on its own; for

restarting the tool unlock on/o switch and switch on tool

again w

AFTER USE

• After switching o the tool, never stop the rotation of the

accessory by a lateral force applied against it

BATTERIES

• The battery supplied is partially charged (to ensure

full capacity of the battery, completely charge the battery

in the battery charger before using your power tool for the

rst time)

• Only use the following batteries and chargers with

this tool

-SKIL battery: BR1*31****

-SKIL charger: CR1*31****

• Do not use the battery when damaged; it should be

replaced

• Do not disassemble the battery

• Do not expose tool/battery to rain

• Permitted ambient temperature (tool/charger/battery):

-when charging 4...40°C

-during operation –20...+50°C

-during storage –20...+50°C

EXPLANATION OF SYMBOLS ON TOOL/BATTERY

3 Read the instruction manual before use

4 Wear protective glasses and hearing protection

5 Batteries may explode when disposed of in re, so do not

burn battery for any reason

6 Store tool/charger/battery in locations where temperature

will not exceed 50°C

7 Do not dispose of electric tools and batteries together

with household waste material

USE

• Charging battery

! read the safety warnings and instructions

provided with the charger

• Removing/installing the battery 2

• Battery level indicator 8

-press the battery level indicator button L to show the

current battery level 8a

! when the lowest level of the battery indicator

8b, the

battery is empty

! 

after pressing button L 8c, the battery is not

within the allowable operating temperature range

• Battery protection

The tool is suddenly being switched o or prevented from

being switched on, when

-the load is too high --> remove load and restart

-the battery temperature is not within the allowable

operating temperature range of -20 to +50°C --> 2

levels of the battery level indicator start ashing when

pressing button L 8c; wait until battery has returned

within the allowable operating temperature range

carefully re-enter the cut. The wheel may bind, walk up

or kickback if the power tool is restarted in the workpiece.

e) Support panels or any oversized workpiece to

minimize the risk of wheel pinching and kickback.

Large workpieces tend to sag under their own weight.

Supports must be placed under the workpiece near the

line of cut and near the edge of the workpiece on both

sides of the wheel.

f) Use extra caution when making a “pocket cut” into

existing walls or other blind areas. The protruding

wheel may cut gas or water pipes, electrical wiring or

objects that can cause kickback.

ADDITIONAL SAFETY INSTRUCTIONS

GENERAL

• This tool is not suitable for wet grinding/cutting

• Only use the anges which are supplied with this tool

• This tool should not be used by people under the age of

16 years

• Remove battery from tool before making any

adjustments or changing accessories

ACCESSORIES

• SKIL can assure awless functioning of the tool only

when original accessories are used

• For mounting/using non-SKIL accessories observe the

instructions of the manufacturer concerned

• Use only grinding/cutting discs with a maximum

thickness of 6 mm and a spindle hole diameter of

22 mm

• Never use reducors or adaptors to t large-hole grinding/

cutting discs

• Never use accessories with a “blind” threaded hole

smaller than M14 x 21 mm

• Handle and store grinding/cutting discs carefully to avoid

chipping and cracking

BEFORE USE

• Before using the tool for the rst time, it is recommended

to receive practical information

• Always mount auxiliary handle E 2 and protective guard

F 2; never use the tool without them

• 

or call the local utility company for assistance

(contact with electric lines can lead to re or electrical

shock; damaging a gas line can result in an explosion;

penetrating a water pipe will cause property damage or

an electrical shock)

• Do not work materials containing asbestos (asbestos

is considered carcinogenic)

• Dust from material such as paint containing lead, some

wood species, minerals and metal may be harmful

(contact with or inhalation of the dust may cause allergic

reactions and/or respiratory diseases to the operator or

bystanders); wear a dust mask and work with a dust

extraction device when connectable

• Certain kinds of dust are classied as carcinogenic

(such as oak and beech dust) especially in conjunction

with additives for wood conditioning; wear a dust

mask and work with a dust extraction device when

connectable

• Follow the dust-related national requirements for the

materials you want to work with

• Be careful when cutting grooves, especially in supporting

walls (slots in supporting walls are subject to country-

specic regulations; these regulations are to be observed

under all circumstances)

Skil 3930 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info