758609
13
Zoom out
Zoom in
Vorherige Seite
1/196
Nächste Seite
13
-do not brake cutting discs with side pressure
Holding and guiding the tool
-always hold the tool rmly with both hands, so you will
have full control of the tool at all times
! while working, always hold the tool at the grey-
coloured grip area(s) t
-provide for a secure stance
-pay attention to the direction of rotation; always hold the
tool so, that sparks and grinding/cutting dust y away
from the body
-keep ventilation slots K 2 uncovered
Mounting/removing spanner C y
-only applicable if tool is executed with auxiliary handle
with integrated spanner storage
APPLICATION ADVICE
For more information see www.skil.com
MAINTENANCE / SERVICE
This tool is not intended for professional use
Always keep tool clean (especially ventilation slots K 2)
! remove battery from tool before cleaning
If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should
be carried out by an after-sales service centre for SKIL
power tools
-send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of the
tool are listed on www.skil.com)
Be aware that damage due to overload or improper
handling of the tool will be excluded from the warranty
(for the SKIL warranty conditions see www.skil.com or
ask your dealer)
ENVIRONMENT
Do not dispose of electric tools, batteries,
accessories and packaging together with household
waste material (only for EU countries)
-in observance of European Directive 2012/19/EC
on waste of electric and electronic equipment and
its implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
-symbol 7 will remind you of this when the need for
disposing occurs
! prior to disposal protect battery terminals with
heavy tape to prevent short-circuit
NOISE / VIBRATION
Measured in accordance with EN 60745 the sound
pressure level of this tool is 81.5 dB(A) and the sound
power level 92.5 dB(A) (uncertainty K = 3 dB), and the
vibration when surface grinding 3.9 m/s² (triax vector
sum; uncertainty K = 1.5 m/s²)
! 

The vibration emission level has been measured in
accordance with a standardised test given in EN 60745;
it may be used to compare one tool with another and as
-the battery is nearly empty (to protect against
deep discharge) --> a low battery level or ashing low
battery level 8b is shown by the battery level indicator
when pressing button L; charge battery
! 

damaged
Mounting of accessories 2
! remove battery from tool
-clean spindle A and all parts to be mounted
-tighten clamping ange B with spanner C while pushing
spindle-lock button D
! push spindle-lock button D only when spindle A is
at a standstill
-for removing accessories handle vice-versa
! grinding/cutting discs become very hot during
use; do not touch them until they have cooled
down
! never use a grinding/cutting disc without the label
(“blotter”) which is glued onto it (if provided)
Mounting of auxiliary handle E 9
! remove battery from tool
-screw auxiliary handle E on the right, the top, or the left
of the tool (depending on the work to be carried out)
Removing/mounting/adjusting of protective guard F q
! remove battery from tool
! ensure that the closed side of the protective guard
always points to the operator
-if necessary, adjust protective guard F by tightening
screw G which is pre-set at manufacturing (ensure
that the protective guard is closed)
Before using the tool
-ensure that accessory is correctly mounted and rmly
tightened
-check if accessory runs freely by turning it by hand
-test-run tool for at least 60 seconds at highest no-load
speed in a safe position
-stop immediately in case of considerable vibration or
other defects and check tool to determine the cause
On/o locking switch J w
-switch on tool wa
! be aware of the sudden impact when the tool is
switched on
! before the accessory reaches the workpiece, the
tool should run at full speed
-lock switch wb
-unlock switch/switch o tool wc
! 
the workpiece
! the accessory continues to rotate for a short time

Grinding e
-move the tool back and forth with moderate pressure
! never use a cutting disc for side grinding
Cutting r
-do not tilt the tool while cutting
-always move the tool in same direction as arrow on tool
head, in order to prevent the tool from being pushed out
of the cut in an uncontrolled manner
-do not apply pressure on the tool; let the speed of the
cutting disc do the work
-the working speed of the cutting disc depends on the
material to be cut
13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Skil 3930 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info