Bedienungsanleitung Skil 5360 (Seite 13 von 172) (Alle Sprachen)

758582

Zoom out

Zoom in

Vorherige Seite

1/172

Nächste Seite

ACCESSORIES

• SKIL can assure awless functioning of the tool only

when original accessories are used

• Use only saw blades that correspond with the

characteristic data given in these operation instructions

and that are tested and marked in accordance with EN

847-1

• Use only accessories with an allowable speed matching

at least the highest no-load speed of the tool

• 



and a spindle hole of 10 mm

• Never use grinding discs with this tool

• Handle and store accessories with care

BEFORE USE

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool

• Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start working

• Be familiar with the controls and the proper use of the

tool

• Remove all obstacles on top of as well as underneath the

cutting path before you start cutting

• Secure the workpiece (a workpiece clamped with

clamping devices or in a vice is held more securely than

by hand)

• 

or call the local utility company for assistance

(contact with electric lines can lead to re or electrical

shock; damaging a gas line can result in an explosion;

penetrating a water pipe will cause property damage or

an electrical shock)

• Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

DURING USE

• The noise level when working can exceed 85 dB(A); wear

ear protection

• Always keep the cord away from moving parts of the tool;

direct the cord to the rear, away from the tool

• Never use the tool without the original protection guard

system

• Do not attempt to cut extremely small workpieces

• Do not work overhead with the power tool (sucient

control of the power tool is not ensured in this working

manner)

• In case of jamming or electrical or mechanical

malfunction, immediately switch o the tool and

disconnect the plug

• If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

AFTER USE

• When you put away the tool, switch o the motor and

ensure that all moving parts have come to a complete

standstill

• After switching o your circular saw, never stop the

rotation of the saw blade by a lateral force applied

against it

EXPLANATION OF SYMBOLS ON TOOL

4 Read the instruction manual before use

5 Double insulation (no earth wire required)

6 Wear protective glasses and hearing protection

7 Do not dispose of the tool together with household waste

material

3) GUARD FUNCTION

a) Check guard for proper closing before each use. Do

not operate the saw if guard does not move freely

and enclose the blade instantly. Never clamp or

tie the guard so that the blade is exposed. If saw is

accidentally dropped, guard may be bent. Check to make

sure that guard moves freely and does not touch the

blade or any other part, in all angles and depths of cut.

b) Check the operation and condition of the guard

return spring. If the guard and the spring are not



use. Guard may operate sluggishly due to damaged

parts, gummy deposits, or a build-up of debris.

c) Assure that the base plate of the saw will not shift

while performing the “plunge cut” when the blade

 Blade shifting sideways will

cause binding and likely kickback.

d) Always observe that the guard is covering the



An unprotected, coasting blade will cause the saw to

walk backwards, cutting whatever is in its path. Be aware

of the time it takes for the blade to stop after switch is

released.

ADDITIONAL SAFETY WARNINGS

GENERAL

• This tool is not intended for use by children and persons

with reduced physical, sensory or mental capabilities,

or lack of experience and knowledge, unless they have

been given supervision or instruction concerning use of

the tool by a person responsible for their safety

• Before using the tool for the rst time, it is recommended

to receive practical information

• This tool is not suitable for wet cutting 3

• Always disconnect plug from power source before

making any adjustment or changing any accessory

• Never use the tool for side grinding

• Never use the tool when the cord is damaged; it must be

replaced by a specially prepared cord available through

the service organization.

• Do not operate the power tool stationary (it is not

designed for operation with a saw table)

• Do not work materials containing asbestos (asbestos

is considered carcinogenic)

• Do not saw ferrous metals (red hot chips can ignite the

dust extraction)

• 

vacuum cleaner must be approved for the extraction

of stone dust (using this equipment reduces dust-

related hazards)

• Dust from material such as paint containing lead, some

wood species, minerals and metal may be harmful

(contact with or inhalation of the dust may cause allergic

reactions and/or respiratory diseases to the operator or

bystanders); wear a dust mask and work with a dust

extraction device when connectable

• Certain kinds of dust are classied as carcinogenic

(such as oak and beech dust) especially in conjunction

with additives for wood conditioning; wear a dust

mask and work with a dust extraction device when

connectable

• Follow the dust-related national requirements for the

materials you want to work with

Skil 5360 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info