Bedienungsanleitung Skil 5360 (Seite 14 von 172) (Alle Sprachen)

758582

Zoom out

Zoom in

Vorherige Seite

1/172

Nächste Seite

! be aware of the sudden impact when the tool is

switched on

! the tool should run at full speed before the blade

enters into the workpiece

! do not force the tool (apply light and continuous

pressure in order to avoid overheating the blade



plastic material)

! 

coloured grip area(s) y

-after completing the cut switch o tool by releasing

trigger B

! ensure that the blade has come to a complete



workpiece

• Plunge cutting u

-switch on the tool

! the tool should run at full speed before the blade

enters into the workpiece

-press knob M with your thumb

-tilt tool forward with line-of-cut indicator R lined up with

desired line of cut marked on the workpiece

-gradually move tool forward

! never pull tool backwards

• Parallel guide S i

-for making exact cuts along a workpiece edge

-can be inserted in either side of foot

Adjusting parallel guide

-loosen knob T

-adjust to desired cutting width by using parallel guide

scale (use line-of-cut indicator R as 0-reference)

-tighten knob T

APPLICATION ADVICE

• Only use sharp saw blades of the correct type o

-use hardened steel saw blade V 2 for cutting wood,

aluminium, plastic and all sorts of laminated wood

-use diamond disc W 2 for cutting ceramics and tiles

-carbide tipped blades X 2 stay sharp up to 30 times

longer than ordinary blades

• Cutting large panels p

-support panel close to the cut either on oor, table or

workbench

! set cutting depth so that you cut through panel

and not through support

-in case parallel guide does not allow desired width of

cut, clamp or nail straight piece of wood to workpiece

as a guide, and use the left side of the foot against this

guide

• Splinter-free cutting

-always face the good side of the workpiece down

-fasten a straight piece of wood on the workpiece by

means of 2 clamps

• For more information see www.skil.com

MAINTENANCE / SERVICE

• This tool is not intended for professional use

• Always keep tool and cord clean (especially ventilation

slots Y 2)

! disconnect the plug before cleaning

• Always keep the area around lower guard Z 2 clean

(remove dust and chips by blowing out with compressed

air or with a brush)

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

•If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

USE

• On/o 8

-switch on tool by rst pressing knob A forward and then

pulling trigger switch B

-switch o tool by releasing trigger switch B

• Adjusting cutting depth (0-28,5 mm) 9

-loosen knob C

-set desired cutting depth using scale D

-tighten knob C

-for an optimal quality cut the saw blade should not

extend more than 3 mm below the workpiece

! 

cutting depth corresponds with value on cutting

depth scale D (for actual depth of cut use table q

as reference)

! 

cut

• Dust suction w

-connect vacuum cleaner hose E to connection F and

vacuum cleaner as illustrated

! never let the vacuum cleaner hose interfere with

the lower guard or the cutting operation

! do not use vacuum cleaner when cutting metal

• Changing saw blade e

! disconnect the plug

! ensure that the blade has come to a complete

standstill

-set cutting depth to the maximum

-take hex key G from storage H

-push spindle-lock button J and hold it while you remove

blade boltK by turning hex key G CLOCKWISE (= in

same direction as arrow printed on saw blade)

! push spindle-lock button J only when tool is at a

standstill

-release spindle-lock button J

-remove ange L

-press knob M with your thumb

-lift up foot N and remove saw blade

! change saw blade with saw teeth and arrow

printed on saw blade pointing in same direction as

arrow on upper guard P e b

-mount ange L

-rmly tighten blade bolt K by turning hex key G

COUNTER-CLOCKWISE while pushing spindle-lock

button J

-release spindle-lock button J

• Operating the tool r

-set desired cutting depth

-connect plug to power source (light Q turns on

indicating that the tool is receiving power) t

-press knob M with your thumb

-place tool with front end of foot at on workpiece

-tilt tool forward with line-of-cut indicator R lined up with

desired line of cut marked on the workpiece

! ensure that the saw teeth are not engaged into the

workpiece

-switch on the tool

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 5360 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info