Bedienungsanleitung Skil 7362 (Seite 9 von 108) (Alle Sprachen)

758394

Zoom out

Zoom in

Vorherige Seite

1/108

Nächste Seite

BEFORE USE

• Always check that the supply voltage is the same as the

voltage indicated on the nameplate of the tool

• Avoid damage that can be caused by screws, nails and

other elements in your workpiece; remove them before

you start working

• Secure the workpiece (a workpiece clamped with

clamping devices or in a vice is held more securely than

by hand)

DURING USE

• The noise level when working can exceed 85 dB(A); wear

ear protection

• Wear protective gloves, safety glasses, close-tting

clothes and hair protection (for long hair)

• Always keep the cord away from moving parts of the tool;

direct the cord to the rear, away from the tool

• Do not touch the moving sanding sheet

• In case of electrical or mechanical malfunction,

immediately switch o the tool and disconnect the plug

• If the cord is damaged or cut through while working, do

not touch the cord, but immediately disconnect the plug

AFTER USE

• When you put away the tool, switch o the motor and

ensure that all moving parts have come to a complete

standstill

EXPLANATION OF SYMBOLS ON TOOL

3 Read the instruction manual before use

4 Double insulation (no earth wire required)

5 Do not dispose of the tool together with household waste

material

WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):

• Do not connect the blue (= neutral) or brown (= live) wire

in the cord of this tool to the earth terminal of the plug

•If for any reason the old plug is cut o the cord of this tool,

it must be disposed of safely and not left unattended

USE

• Mounting of sanding sheet 6

! disconnect the plug

! the dust suction requires the use of perforated

sanding sheets

! use paper punch D for adapting non-perforated

sanding sheets to dust suction 7

! perforation in sanding sheet should correspond

with perforation in sanding foot

! replace worn sanding sheets in time

! always use the tool with the total sanding surface

covered with sanding paper

• On/o switch

-switch on/o the tool by pushing switch A 2 forward/

backwards

! before the sanding surface reaches the workpiece,

you should switch on the tool

! 

the workpiece

• Dust suction

! do not use dust box/vacuum cleaner when

sanding metal

Dust box 8

-empty dust box B regularly for optimal dust pick-up

performance

-remove dust box B by pulling dust box B backwards

For using vacuum cleaner

-mount vacuum cleaner adapter C as illustrated 9a

tool or these instructions to operate the power tool.

Power tools are dangerous in the hands of untrained

users.

e) Maintain power tools and accessories. Check for

misalignment or binding of moving parts, breakage



power tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are caused

by poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are less

likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc.,

in accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations dierent

from those intended could result in a hazardous situation.

h) Keep handles and grasping surfaces dry, clean

and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and

control of the tool in unexpected situations.

5) SERVICE

a) 

person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained.

SAFETY INSTRUCTIONS FOR SANDERS

GENERAL

• This tool should not be used by people under the age of

16 years

• Use completely unrolled and safe extension cords with a

capacity of 16 Amps (U.K. 13 Amps)

• Never use the tool when the cord is damaged; it must be

replaced by a specially prepared cord available through

the service organization.

• Dust from material such as paint containing lead, some

wood species, minerals and metal may be harmful

(contact with or inhalation of the dust may cause allergic

reactions and/or respiratory diseases to the operator or

bystanders); wear a dust mask and work with a dust

extraction device when connectable

• Certain kinds of dust are classied as carcinogenic

(such as oak and beech dust) especially in conjunction

with additives for wood conditioning; wear a dust

mask and work with a dust extraction device when

connectable

• Follow the dust-related national requirements for the

materials you want to work with

• Do not work materials containing asbestos (asbestos

is considered carcinogenic)

• When sanding metal, sparks are generated; do not

use dust box and keep other persons and combustible

material from work area

• Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the housing and

excessive accumulation of powdered metal may cause

electrical hazards.

• Always disconnect plug from power source before

making any adjustment or changing any accessory

ACCESSORIES

• SKIL can assure awless functioning of the tool only

when original accessories are used

• Do not continue to use worn, torn or heavily clogged

sanding sheets

Skil 7362 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info