Bedienungsanleitung Skil 8040 (Seite 8 von 124) (Alle Sprachen)

758005

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

• Memory setting 9 (8040)

-to select one of the four stored memory settings press

button P

-to store a temperature and air ow setting press

button P to select a memory location, set the desired

temperature and airow, and press and hold button N

to store the setting

• General use

-determine the right temperature by testing out on an

inconspicuous part of the workpiece; start with a low

temperature setting

-the temperature drops as the distance between the air

outlet/nozzle and the workpiece increases

-the temperature required depends on the material to

be worked on

• Stationary use q

-set the tool down on its rear in an upright position

-make sure the surface is clean and dustfree; polluted

air damages the motor

-make sure the air ow is directed away from you

-secure the cord to prevent pulling down the tool

-do not touch the air outlet/nozzle

-make sure nothing drops into the air outlet/nozzle

-carefully hold the tool with one hand while switching it

o with the other hand, and then allow it to cool down

• Holding and guiding the tool w

-hold the tool with one hand

-keep ventilation slots F 2 uncovered

• Standard accessories 2

-glass protection nozzle G (for deecting air ow)

-round nozzle H (for concentrating air ow)

-reector nozzle J (for reecting air ow)

-reduction nozzle K (for concentrating air ow)

NOTES:

-all application examples (except removing paint

next to glass) can be performed without accessories;

however, using the appropriate accessory simplies the

work and signicantly improves the quality of the results

-this tool can also be used in combination with

commonly available accessories for heat guns

• Mounting/removing accessories

-simply t the accessory onto air outlet L 2

-remove an accessory by pulling it o to the front after it

has cooled down

! mount an accessory only when the air outlet is

cold, when the switch is in position “0” and when

the plug is disconnected

-use nozzle release ring E for easy removing hot nozzles

• Constant heat control (overload protection)

Protects heating element from damage when tool is

overloaded without having to stop it and/or let it cool

down for a period of time

-when the temperature gets too high, the heating

element switches itself o, while the motor continues to

run and produces cold air

-when the temperature has dropped suciently (taking

only a few seconds), the heating element will be

switched on automatically

! 

high temperature setting, and switched on again

after a short break, it may take a while before the

heating element reaches the desired temperature

• Keep work area clean and well lit

• Stay alert; watch what you are doing, use common sense

and do not operate the tool when you are tired

• Take a secure stance; do not overreach, especially on

ladders and stages

• Ensure that the tool is switched o, before putting it aside

• In case of electrical or mechanical malfunction,

immediately switch o the tool and disconnect the plug

AFTER USE:

-set the tool down on its rear in an upright position

• Switch o the tool and disconnect the plug

• Allow the tool to cool down for at least 30 minutes before

storage

• Do not store/leave the tool outdoors

• Store the tool in a dry and locked-up place, out of reach

of children

EXPLANATION OF SYMBOLS ON TOOL

3 Read the instruction manual before use

4 Double insulation (no earth wire required)

5 Do not dispose of the tool together with household waste

material

USE

• On/o switch with temperature settings 6

! check if switch A 2 is in position “0” before

plugging in

-switch on the tool by pushing switch A in desired

position:

8020

I = 50°C, air ow 350 litres/minute

II = 450°C, air ow 350 litres/minute

III = 600°C, air ow 500 litres/minute

8040

I = 50°C + air ow 250-500 litres/minute

II = 50°C ... 650°C, air ow 250-500 litres/minute

-when using it for the rst time, some smoke may emit

from the tool; this is normal and will soon cease

-switch o the tool by pushing switch A in position “0”

• Temperature setting

! there is a tolerance on the indicated temperatures

50...90°C: max 90°C

less than 300°C: ±20%

more than 300°C: ±10%

8020

-use dial wheel M to select the desired temperature

setting

-use table 6 for reference

8040 7

-set desired target temperature in steps of 10°C by

pressing buttons B briey

-pressing buttons B constantly increases/decreases

the target temperature continuously until the buttons

are released or the minimum/maximum temperature is

reached

-after the target temperature is set, display D shows

ashing arrows until the desired temperature is reached

(in position “II” only)

-the target temperature will be stored in the memory of

the tool, so that each time after switching on the tool

heats up to the last selected target temperature

• Air ow setting 8 (8040)

-set desired air ow in steps of 50 l/min by pressing

buttons C briey

-display D shows the actual air ow setting in a bar

graph

Skil 8040 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info