Bedienungsanleitung Skil 8700 (Seite 10 von 92) (Alle Sprachen)

758639

Zoom out

Zoom in

Vorherige Seite

1/92

Nächste Seite

- mount 4 casters D as illustrated

- the appliance is ready for dry vacuum cleaning with

cartridge lter E pre-installed

- place motor head back onto container and secure it

into place by using both latches A

- mount vacuum hose F onto hose connection G and

screw it into place

- insert extension tubes H and handle J rmly into each

other and connect them to the vacuum hose

- mount desired nozzle K, L or M onto suction tube

• On/o 5

- set switch N to position “I” to start wet or dry

vacuum cleaning

- set switch N to position “O” for switching o the

vacuum cleaner

- when connecting a power tool directly to the vacuum

cleaner, universal power tool adapter P may be used

(if needed)

• Airow control 6

Control the airow by sliding regulator Q up or down the

opening in handle J

• Mounting/removing of cartridge lter 7

! disconnect the plug

- mount/remove cartridge lter E as illustrated

- mount protection lter R over cartridge lter E for

prolonging its service life and easy cleaning purposes

• Dry vacuum cleaning 8

! ensure that all information mentioned in the

chapter “SAFETY” is read and understood

! inform yourself beforehand about the handling of

materials that are hazardous to one’s health

- verify that cartridge lter E 3 and protection lter R 3

are securely mounted

- insert dust bag S as illustrated (when using a dust bag,

cartridge lter E 3 clogs slower, the vacuuming

performance is kept longer and the disposal of dust

becomes easier)

- only vacuum directly in the container when materials

not hazardous to one’s health are being vacuumed

- switch o the appliance and disconnect the plug

after vacuuming

• Wet vacuum cleaning 9

! ensure that all information mentioned in the

chapter “SAFETY” is read and understood

! inform yourself beforehand about the handling of

materials that are hazardous to one’s health

! remove dust bag S, cartridge filter E and

protection filter R before starting wet vacuuming

- ensure that container C 3 is emptied and clean

- carefully mount foam sleeve lter T as illustrated

- secure motor head back on the container, mount

desired nozzle directly onto vacuum hose or extension

tube, and switch on the appliance

- do not immerse the nozzle completely in the liquid;

leave a gap at the nozzle opening to allow air inow

- when the container reaches its maximum capacity, the

motor speed increases

- when this happens, switch o the appliance,

disconnect the plug, and empty the container 0

- switch o the appliance and disconnect the plug

after vacuuming

- clean and dry the inside and outside of the container

before storage 0

• Mounting/removing of HEPA lter !

! disconnect the plug

- unlock lter door X as illustrated and pull it out

- remove HEPA lter Z and clean it or mount a new one

- insert tabs of lter door X into upper slots and lock it

into place

• Storage of tubes and nozzles @

MAINTENANCE / SERVICE

• Always disconnect plug from power source before

cleaning and/or maintenance

• Store the appliance indoors in a dry place

• Keep appliance clean (especially ventilation slots V 3)

- clean ventilation slots V 3 regularly with a brush or

compressed air

! do not attempt to clean ventilation slots by

inserting pointed objects through openings

• Cleaning of cartridge lter #

- regularly clean the carefully removed cartridge lter by

gently tapping or brushing dirt o (wear dust mask)

- do not clean indoors in living areas

! do not wash filter with soap and water

- for picking up dust the cartridge lter needs to be dry

- if the cartridge lter is wet, it will clog quickly and be

very dicult to clean

- handle the cartridge lter carefully when removing,

cleaning or replacing it

! do not use a cartridge filter with tears or small

holes; replace it immediately

• Cleaning of foam sleeve lter $

- wash lter with mild soap and water and rinse it with

clean water

- allow lter to dry before mounting it again

• Cleaning of HEPA lter %

- clean lter by brushing dirt o (wear dust mask)

- for optimal performance mount a new lter (for

ordering see “Service” on www.skilmasters.com)

• If the appliance should fail despite the care taken in

manufacturing and testing procedures, repair should be

carried out by an after-sales service centre for SKIL

power tools

- send the appliance undismantled together with proof

of purchase to your dealer or the nearest SKIL service

station (addresses as well as the service diagram of

the appliance are listed on www.skilmasters.com)

TROUBLESHOOTING

• The following listing shows problem symptoms, possible

causes and corrective actions (if these do not identify

and correct the problem, contact your dealer or

service station)

! switch off the tool and disconnect the plug before

investigating the problem

★ Appliance does not operate

- no power supply -> check power supply (power cable,

circuit breakers, fuses)

- faulty power cable -> unplug and check power cable; if

damaged, have it repaired by a professional

- container full -> empty container

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skil 8700 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info