Bedienungsanleitung Skil 9412 (Seite 8 von 178) (Alle Sprachen)

644813

Zoom out

Zoom in

Vorherige Seite

1/178

Nächste Seite

loading and susceptibility to twisting or binding of the

wheel in the cut and the possibility of kickback or wheel

breakage.

b) Do not position your body in line with and behind

the rotating wheel. When the wheel, at the point of

operation, is moving away from your body, the possible

kickback may propel the spinning wheel and the power

tool directly at you.

c) When the wheel is binding or when interrupting a



hold the power tool motionless until the wheel

comes to a complete stop. Never attempt to remove



motion, otherwise kickback may occur. Investigate

and take corrective action to eliminate the cause of

wheel binding.

d) Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed and

carefully re-enter the cut. The wheel may bind,

walk up or kickback if the power tool is restarted in the

workpiece.

e) Support panels or any oversized workpiece to

minimize the risk of wheel pinching and kickback.

Large workpieces tend to sag under their own weight.

Supports must be placed under the workpiece near the

line of cut and near the edge of the workpiece on both

sides of the wheel.

f) Use extra caution when making a “pocket cut” into

existing walls or other blind areas. The protruding

wheel may cut gas or water pipes, electrical wiring or

objects that can cause kickback.

5) SAFETY WARNINGS SPECIFIC FOR SANDING

OPERATIONS

a) Do not use excessively oversized sanding disc

paper. Follow manufacturers recommendations,

when selecting sanding paper. Larger sanding paper

extending beyond the sanding pad presents a laceration

hazard and may cause snagging, tearing of the disc, or

kickback.

6) SAFETY WARNINGS SPECIFIC FOR POLISHING

OPERATIONS

a) Do not allow any loose portion of the polishing

bonnet or its attachment strings to spin freely. Tuck

away or trim any loose attachment strings. Loose

and spinning attachment strings can entangle your

ngers or snag on the workpiece.

7) SAFETY WARNINGS SPECIFIC FOR WIRE

BRUSHING OPERATIONS

a) Be aware that wire bristles are thrown by the brush

even during ordinary operation. Do not overstress

the wires by applying excessive load to the brush.

The wire bristles can easily penetrate light clothing and/

or skin.

b) If the use of a guard is recommended for wire

brushing, do not allow any interference of the

wire wheel or brush with the guard. Wire wheel or

brush may expand in diameter due to work load and

centrifugal forces.

GENERAL

 This tool is not suitable for wet grinding/cutting

 Only use this tool for dry polishing

 Only use the anges which are supplied with this tool

the point of pinching. Abrasive wheels may also break

under these conditions.

 Kickback is the result of power tool misuse and/or

incorrect operating procedures or conditions and can be

avoided by taking proper precautions as given below.

a) 

your body and arm to allow you to resist kickback

forces. Always use auxiliary handle, if provided, for

maximum control over kickback or torque reaction

during start-up. The operator can control torque

reactions or kickback forces, if proper precautions are

taken.

b) Never place your hand near the rotating accessory.

The accessory may kickback over your hand.

c) Do not position your body in the area where power

tool will move if kickback occurs. Kickback will

propel the tool in the direction opposite to the wheel’s

movement at the point of snagging.

d) Use special care when working corners, sharp

edges etc. Avoid bouncing and snagging the

accessory. Corners, sharp edges or bouncing have a

tendency to snag the rotating accessory and cause loss

of control or kickback.

e) Do not attach a saw chain woodcarving blade

or toothed saw blade. Such blades create frequent

kickback and loss of control.

3) SAFETY WARNINGS SPECIFIC FOR GRINDING AND

ABRASIVE CUTTING-OFF OPERATIONS

a) Use only wheel types that are recommended for



for the selected wheel. Wheels for which the power

tool was not designed cannot be adequately guarded

and are unsafe.

b) The grinding surface of the centre depressed

wheels must be mounted below the plane of the

guard lip. An improperly mounted wheel that projects

through the plane of the guard lip cannot be adequately

protected.

c) The guard must be securely attached to the power

tool and positioned for maximum safety, so the

least amount of wheel is exposed towards the

operator. The guard helps to protect the operator from

broken wheel fragments, accidental contact with wheel

and sparks that could ignite clothing.

d) Wheels must be used only for recommended

applications. For example: Do not grind with the side of

a cut-o wheel. Abrasive cut-o wheels are intended for

peripheral grinding; side forces applied to these wheels

may cause them to shatter.

e) 

correct size and shape for your selected wheel.

Proper wheel anges support the wheel thus reducing

the possibility of wheel breakage. Flanges for cut-o

wheels may be dierent from grinding wheel anges.

f) Do not use worn down wheels from larger power

tools. A wheel intended for a larger power tool is not

suitable for the higher speed of a smaller tool and may

burst.

4) ADDITIONAL SAFETY WARNINGS SPECIFIC FOR

CUTTING OFF OPERATIONS

a) 

pressure. Do not attempt to make an excessive

depth of cut. Overstressing the wheel increases the

Skil 9412 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info