Bedienungsanleitung Skoda Rapid - 2015 (Seite 161 von 200) (Englisch)

617604

161

Zoom out

Zoom in

Vorherige Seite

1/200

Nächste Seite

Installing

›

Push the cap onto the wheel bolt up to the stop.

Changing a wheel

When changing a wheel, the following instructions must be followed.

›

Remove the full wheel trim or the caps of the wheel bolts.

›

First of all slacken the anti-theft wheel bolt and then the other wheel bolts.

›

Jack up the vehicle until the wheel that needs changing is clear of the

ground.

›

Unscrew the wheel bolts and place them on a clean surface (cloth, paper,

etc.).

›

Remove the wheel carefully.

›

Attach the spare wheel and slightly screw on the wheel bolts.

›

Lower the vehicle.

›

Alternately tighten wheel bolts opposite (diagonally) with the wheel wrench.

Tighten the anti-theft wheel bolt last.

›

Replace the wheel trim or the caps.

When fitting unidirectional tyres, ensure that the direction of rotation is cor-

rect » page 151.

WARNING

■

Undo the wheel bolts only a little (about one turn) provided that the vehi-

cle has not yet been jacked up. Otherwise the wheel could become loose

and fall off.

■

All bolts must be clean and must turn easily.

■

If it is established when changing a wheel that the wheel bolts are corro-

ded and difficult to move, then these must be replaced.

■

Under no circumstances grease or oil the wheel bolts!

Follow-up work

After changing the wheel, the following work must be carried out.

›

Stow and attach the replaced wheel in the spare wheel well using a special

screw » page 155.

›

Stow the tool kit in the space provided and secure using the band.

›

Check the tyre pressure on the installed spare wheel as soon as possible.

›

Have the tightening torque of the wheel bolts checked with a torque

wrench as soon as possible.

After changing the wheel, the tyre pressure should be adjusted. In vehicles

with tyre pressure monitoring, tyre pressure values are to be stored » page 115.

Replace the damaged wheel or consult a specialist garage about repair op-

tions.

WARNING

Information on the wheel bolts

■

The prescribed tightening torque of the wheel bolts for steel and light al-

loy wheels is 120 Nm.

■

If the wheel bolts are tightened to a too low tightening torque, the rim

can come loose when the car is moving. A tightening torque which is too

high can damage the bolts and threads and this can result in permanent

deformation of the contact surfaces on the rim.

■

In case of incorrect treatment of the wheel bolts, the wheel can loosen

when the car is moving.

■

Drive cautiously and only at a moderate speed until the tightening torque

has been checked.

Loosening/tightening wheel bolts

Fig. 133

Changing a wheel: Loosening the

wheel bolts

Before removing the wheel bolts, the caps for the wheel bolts must be pulled

off.

Release

›

Push the wheel wrench onto the wheel bolt to the stop



Use the appropriate adapter for undoing and tightening the anti-theft wheel bolts » page 160.

158

Do-it-yourself

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skoda Rapid - 2015 Seite 161

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Skoda Rapid - 2015

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info