Bedienungsanleitung Skytech 3002 (Seite 6 von 10) (Englisch)

603162

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

SYSTEM CHECK

MILLIVOLT VALVES

Light the gas appliance following the lighting instructions that came with the appliance. Conrm that the pilot ame is ON;

and the control knob on the gas valve is in the ON position for the main gas valve to operate.

Skytech: 3002

REV. 4-19-12 Page 6

• Slide the 3-position button on the remote receiver to the ON position (Fig. 16). The main gas ame (re) should light.

• Slide the button to OFF. The ame should extinguish (the pilot ame will remain ON).

• Slide the button to REMOTE (the center position), and then press the MODE button on the transmitter to change

the system to ON. The main gas ame should ignite.

• Press the MODE button on the transmitter to change the system to OFF. The ame should extinguish (the pilot

ame will remain on).

• Press the MODE button on the transmitter to change the system to THERMO. Advance the SET temperature on the

transmitter to a temperature of a least 2°F (1°C) above the ROOM temperature displayed on the LCD screen. With this

manual setting, the normal thermostatic cycle is overridden and the system ame will ignite. Place the SET temperature

to at least 2°F (1°C) below the room temperature and the system ame will extinguish in a few seconds. Thereafter, it

should continue to cycle on and off thermostatically approximately every two minutes as the ROOM temperature changes,

but only when the temperature differential between ROOM and SET temperatures differ at least 2°F (1°C). (The 2°F

differential is the factory setting.)

ELECTRONIC IGNITION SYSTEMS

Light the gas appliance following the lighting instructions that came with the appliance. Conrm that the pilot ame is ON;

and the control knob on the gas valve is in the ON position for the main gas valve to operate.

• Slide the 3-position button on the remote receiver to the ON position. The spark electrode should begin sparking to

ignite the pilot (the pilot may ignite after only one spark). After the pilot ame is lit, the main gas valve should open and

the main gas ame should ignite.

• Slide the button to OFF. The main gas ame and pilot ame should BOTH extinguish.

• Slide the button to REMOTE (the center position), and then press the MODE button on the transmitter to change the

system to ON. The spark electrode should begin sparking to ignite the pilot. After the pilot is lit, the main gas valve

should open and the main gas ame should ignite.

• Press the MODE button on the transmitter to OFF. The main gas ame and pilot ame should BOTH extinguish.

• Press the MODE button on the transmitter to change the system to THERMO. Advance the SET temperature on the

transmitter to a temperature at least 2°F (1°C) above the ROOM temperature displayed on the LCD screen. With this

manual setting the normal thermostatic cycle is overridden and the system ame will ignite. Place the SET temperature at

least 2°F (1°C) below the room temperature and the system ame will extinguish in a few seconds. Thereafter, it should

continue to cycle ON and OFF thermostatically approximately every two minutes as the ROOM temperature changes, but

only when the temperature differential between ROOM and SET temperatures differ at least 2°F (1°C). (The 2°F

differential is the factory setting.)

TRANSMITTER

TRANSMITTER OPERATING DISTANCE

The SKYTECH remote control operates on RF (radio frequency) signals that are sent by the TRANSMITTER (remote)

to the RECEIVER that operates the appliance. It is recommended that the TRANSMITTER always be located within the

20-foot operating range, preferably in the same room in which the appliance is located.

GENERAL INFORMATION

THERMO UPDATING FEATURE IN TRANSMITTER

This SKYTECH remote control has a THERMO UPDATING Feature built into its software. The THERMO UPDATING

Feature operates in the following manner, but only in the THERMO and PROGRAM MODES:

The transmitter normally reads the ROOM temperature every 2 minutes; checking the ROOM temperature against the

SET temperature by sending a signal to the receiver.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skytech 3002 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info