Bedienungsanleitung Skytech 3002 (Seite 7 von 10) (Englisch)

603162

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

Skytech: 3002

REV. 4-19-12 Page 7

COMMUNICATION SAFETY FEATURE IN TRANSMITTER

This SKYTECH series remote controls have a COMMUNICATION – SAFETY function built into the software. It provides

an extra margin of safety when the TRANSMITTER is out of the normal 20-foot operating range of the receiver.

The COMMUNICATION – SAFETY feature operates in the following manner for all OPERATING MODES: ON/THERMO/

OFF.

At all times and in all OPERATING MODES, the transmitter sends an RF signal every fteen (15) minutes, to the receiver,

indicating that the transmitter is within the normal operating range of 20-feet. Should the receiver NOT receive a

transmitter signal every 15 minutes, the IC software, in the RECEIVER will begin a 2-HOUR (120-minute) countdown

timing function. If during this 2-hour period, the receiver does not receive a signal from the transmitter, the receiver will

shut down the replace being controlled by the receiver. The RECEIVER will then emit a series of rapid “beeps” for a

period of 10 seconds. Then after 10 seconds of rapid beeping, the RECEIVER will continue to emit a single “beep” every

4 seconds until a transmitter signal is again received. The intermittent 4 second beeping will go on for as long as the

receiver’s batteries last which could be in excess of one year.

To “reset” the RECEIVER and operate the replace system, you must press the MODE button on the transmitter. The

word ON must display on the LCD screen. By turning the system to ON, the COMMUNICATION SAFETY operation is

overridden and the system will return to normal operation depending on the MODE selected at the transmitter.

The COMMUNICATION SAFETY feature will reactivate should the transmitter be taken out of the normal operating range

or should the transmitter’s batteries fail or be removed.

ADDITIONAL PROGRAMMING FEATURES OF THE TRANSMITTER

ROOM

SET

Fig. 17 Thermo ON

MODE

SETTING THE DESIRED ROOM TEMPERATURE

This remote control system can be thermostatically controlled when the transmitter is in THERMO mode (THERMO must

be displayed on the screen). To set the DESIRED room temperature, press the MODE button to place transmitter into

THERMO mode (Fig. 17), then press the UP or DOWN

button to select desired room temperature. The highest SET

temperature is 99° F (32° C); the lowest SET temperature is

45° F (6° C).

OPERATIONAL NOTE: TO CONSERVE BATTERY POWER, CHANGES IN ROOM TEMPERATURE ARE AUTO-

MATICALLY UPDATED EVERY TWO MINUTES TO THE TRANSMITTER.

The Thermo Mode on the transmitter operates the appliance whenever the ROOM TEMPERATURE varies a certain

number of degrees from the SET TEMPERATURE. This variation is called the “SWING” or TEMPERATURE

DIFFERENTIAL. The normal operating cycle of an appliance may be 2-4 times per hour depending on how well the

room or home is insulated from the cold or drafts. A smaller “swing number” increases the number of cycles so the room

temperature is more constant. A larger “swing number” decreases the number of cycles, which saves energy, in most

cases. The factory setting for the “swing number” is 2. This represents a temperature variation of +/- 2° F (1° C) between

SET temperature and ROOM temperature, which determines when the replace will be activated. The “SWING” number

values are: 1=+ 1° F (.5° C), 2= + 2° F (1° C) and 3 = + 3° F (1.6 C).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Skytech 3002 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info