Bedienungsanleitung Smoov One O10 (Seite 12 von 37) (Englisch)

785804

Zoom out

Zoom in

Vorherige Seite

1/37

Nächste Seite

2.4 Setting the control unit

If desired or necessary, the position of the display [12] can be adjusted.

•Switch off the drive unit completely (see chapter 3.6.2).

•Open the cover [13] of the control unit.

•Loosen the three screws [26] on the back of the control unit by not more than half

a turn. To this end, use an Allen key, size 2.5.

•Turn the ring [25] until the display [12] is in the desired position. Then carefully

tighten the three screws [26] until the ring [25] can no longer be turned.

•Close the cover [13] of the control unit.

3. Drive mode

3.1 Switching on the system

The drive and control unit need to be switched on for use be possible. Carry out the fol-

lowing steps to this end:

•Switch off all Bluetooth devices in your immediate vicinity to prevent any interference

with the connection between the drive unit and control unit.

•Ensure that the drive wheel [8] is correctly aligned with the drive unit (see chapter 3.4).

•Briefly press the button [3] on the drive unit. This switches on the drive unit. A brief

acoustic signal sounds, the button [3] lights up green, and the display [2] indicates

the capacity of the battery. (see chapter 5.1). The position light [7] now lights up as

well.

•Switch on the control unit (this needs to be in the mount [16]) by pressing the but-

ton [10] on it for approx. 2 seconds.

•The LED [f] now indicates the capacity of the control unit battery in different colours

(see chapter 5.2). If the LED [f] is flashing blue, this indicates an attempt to establish

a connection to the drive unit via Bluetooth.

•If no Bluetooth connection is established within 10 seconds, the LED [f] flashes red

for 20 seconds. The control unit then switches off.

•If the Bluetooth connection is established between the drive unit and the control

unit, the LED [f] on the control unit lights up continuously. See chapter 5.2. for the

meaning of colour. The capacity of the drive unit battery is also displayed.

If no Bluetooth connection is established after you have performed the steps listed

above, this may be due to the following reasons:

Incorrect alignment of the drive wheel

If the drive wheel [8] is in an incorrect position (see chapter 3.4), the drive unit cannot

be switched on. Instead, the On/Off button [3] lights up green and the LED [c] in the

display [2] flashes white.

Drive unit battery is empty

If the battery no longer has sufficient capacity, the LED [a] flashes briefly in the display

[2] when the SMOOV O10 is switched on. The system switches off completely thereafter.

Charge the battery as described in chapter 4.1.

The control unit battery is empty

If the battery no longer has sufficient capacity, the LED [f] flashes briefly in the display

[12] when the control unit is switched on. The system switches off completely thereafter.

Charge the battery as described in chapter 4.2.

Error in the system

In this regard, see the explanations in chapter 6.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Smoov One O10 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Smoov One O10

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info