Bedienungsanleitung Snooper S3 (Seite 12 von 14) (Englisch)

619690

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

Power Connection

Using the cigarette lighter socket

The S3 comes with a power cable designed to plug into your vehicles

cigarette lighter socket. Take the lead and plug the smaller end into the

DC 12v input socket on the back of the S3 and the cigarette lighter

adaptor in your vehicles cigarette lighter socket.

Please Note: Do not leave your S3 plugged into the cigarette lighter

socket when you start your vehicle. The cigarette lighter socket is prone

to power surges when the vehicle is started that may damage your unit.

If the device does not power up please check that the cigarette lighter

socket is clean of any debris, remembering not to insert any metal objects

into the socket, check that the cigarette lighter adaptor is inserted all the

way into the socket and to check that the fuse in the cigarette lighter

adaptor is operational. If your S3 will still not power up, please check that

the cigarette lighter in your vehicle is functioning correctly.

Replacing the Fuse

If the detector stops operating, the fuse in the cigarette lighter plug might

be blown. If it has blown, follow these steps to replace it with a 2 amp, 5 x

20mm, fast acting fuse.

Caution: Using a fuse that does not meet these ratings or defeating fuse

protection can damage your detector, the power cable, or the vehicles

electrical system.

1. Grasp the ring near the tip of the cigarette lighter plug, then carefully

unscrew the ring by turning it counterclockwise.

- Next use a damp cloth to thoroughly clean the bottom of the S100-RLD

and the side of the bracket where you intend to mount the device.

- Peel the backing paper from one side of the double-sided tape and

apply it to the bottom of the unit.

- Next remove the backing paper from the

other side of the tape and position the

S100-RLD onto the ’L’ shaped bracket as

indicated in the diagram below ensuring

that the front of the detector is facing

forwards down the road. Please note

it will take approximately 24hrs for the

double sided tape to adhere properly to the

bracket and unit.

- Feed the cable from the S100-RLD through

an existing grommet in the bulkhead to

the cockpit of the vehicle and plug the

end of the cable into the socket on the

side of the S3 marked ’RD’. If there

is not a convenient grommet to

use you will need to drill an

additional hole sealed with a

grommet, large enough to feed

the cable and plug through.

Ensure that the cable running

from the S100-RLD to the

S3 is secured periodically

so that it does not interfere with

any of the workings of the vehicle.

Mounting Notes

When mounting the S100-RLD always ensure that you mount the unit

away from any moving parts such as air cooling fans or the fan belt.

Always position the unit so that you can safely feed the cable back

through to the cockpit of the vehicle without the cable interfering with any

moving parts within the engine bay or interfering with any part of the

vehicle that could endanger you or your passengers. Please check that

all surfaces are safe to drill through before beginning any work.

IMPORTANT

If you are unfamiliar with any of the above procedures, please

consult a professional auto electrician.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Snooper S3 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info