Bedienungsanleitung Snooper S3 (Seite 13 von 14) (Englisch)

619690

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

Caution: If you must use pliers to loosen the ring, be careful not to crush

the tip. Never use pliers or other tools to retighten the ring on the

cigarette lighter plug.

2. Pull the ring straight out, then remove the metal tip, spring and old

fuse.

3. Check the fuse to see if it has blown. If it has, replace it.

4. Replace the metal tip and spring inside the ring, then place the fuse

inside the cigarette lighter plug and screw the ring back onto the

plug. Make sure the metal tip is visible when you reassemble the

cigarette lighter plug.

Direct connecting/hard wiring your S3 neo.

You can power your Snooper S3 by wiring it directly to your vehicles 12v

electrical system using the ’Hard Wire’ cable supplied as standard with

your unit. Firstly connect the positive side of the cable (Red) to a 12v

switched live. This is a live that is On when the ignition is On and Off

when the ignition is Off. The negative side of the lead should be

connected to a negative ground, so can be attached to any metal portion

of the vehicles frame. Next plug the small adaptor on the other end of the

lead into the DC 12V input socket on the back of the unit.

Important: If you are unfamiliar with this procedure, please consult a

professional auto electrician

3. S100-RLD External Installation

As the S100-RLD is waterproof it can be mounted outside the vehicle

with the ’L’ shaped bracket, water resistant double sided tape and screw

pack provided.

- Find a suitable mounting position for the detector, ensuring that the

front of the unit has a clear view of the road ahead and is unobstructed

by any metallic objects and that there is a sufficient mounting area to

attach the ’L’ shaped fixing bracket. The S100-RLD needs to be

mounted in as horizontal a position as possible so that it is looking

directly down the road ahead but can be mounted either flat or on it’s

side if necessary. We recommend that you mount the detector either

behind the vehicles grille (If the openings of the grille are at least 10mm

in diameter) or within an air intake at the front of the vehicle. The S100-

RLD can be mounted anywhere at the front of the vehicle, but for

optimum performance we suggest you mount it as close to the

number plate of the vehicle as possible.

- When you have found a suitable location, using the ’L’ shaped mounting

bracket as a template, drill between 2 and 4 pilot holes into the selected

mounting surface for attaching the bracket using either the self-tapping

screws or the nuts and bolts provided.

You will need to attach the bracket using

at least 2 screws or 2 nuts and bolts to

ensure that the bracket is well secured.

Remember that there is a lot of

vibration within the engine bay

so it is very important that the

S100-RLD mounting bracket

is secured correctly.

Typical Fitting

10mm

Minimum

Typical Fitting

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Snooper S3 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info