Bedienungsanleitung Snooper Sapphire (Seite 13 von 24) (Englisch)

619693

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

MEM

MUTE

3. Adjusting the Volume

The Snooper Sapphire has an adjustable volume

for controlling the loudness of the audible alert.

To increase the volume push the ‘OK’ control on

the right hand side of the unit upwards.

To decrease the volume of the unit push the

‘OK’ control downwards.

4. MEM Button

If in the unlikely event that you pass a location of a fixed safety camera and your Snooper Sapphire does not

provide you with an alert, you have the opportunity to store the coordinates of this location manually. Simply

park safely as close as possible to the fixed safety

camera site and press and hold the ‘MEM’ button

for approximately two seconds.

A screen will be displayed asking if you want to

‘Save User Position?’ Use the ‘OK’ control to

highlight ‘Yes’ and then press the ‘OK’ control

to confirm.

When you next pass the fixed safety camera site

again your Snooper Sapphire will now alert you to

the new location. User points can be edited so that

the correct alert for that camera location is given.

As the unit does not know what type of system you are

passing until the user point is edited the unit will alert to the coordinate as a high risk zone (See ‘User Points’

on page 17). Your unit can hold up to 99 coordinates in its memory.

5. MUTE Button

If during an alert you decide that you would like to mute the audible alert, but still retain a visual alert simply

press the MUTE button. The screen will continue to display a visual alert but no audible alert will be produced.

After you have travelled out of range of that location the unit will automatically reset so that the next time you

encounter a fixed speed camera location you will receive both an audible and a visual alert as normal.

6. Cancelling an Alert

If during an alert you decide that you would like to cancel it simply press and hold either the MEM or MUTE

buttons. The display will confirm that the alert has been cancelled and will return to the standby screen.

7. Logic Modes

There are three Logic modes that you can select on your Snooper Sapphire. These different Logic settings

determine how the Sapphire alerts you to fixed speed safety cameras.

Logic 1

When in Logic 1 your unit will alert you both audibly and visually to fixed safety cameras on both sides of the

carriageway as you approach them.

Logic 2 (Factory Default Setting)

When Logic 2 is selected your unit will alert you both audibly and visually as you approach fixed safety cam-

eras on your side of the carriageway only.

Logic 3

When Logic 3 is selected your unit will alert you to fixed safety cameras on both sides of the carriageway but

will alert you audibly in different tones depending on your user settings. If, for example, you select the ‘Hard’

tone for alerting you to fixed safety cameras then you will be alerted to a camera on your side of the road in a

‘Hard’ tone but if the camera is on the opposite side of the road the audible alert provided will be in the ‘Soft’

tone and vice versa.

To change the Logic Mode of your unit please refer to the ‘Logic’ section on page 18.

Back to contents

MEM

MUTE

Save User Point?

YES

Set Volume

0 100

- +

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Snooper Sapphire Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Snooper Sapphire

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info