Bedienungsanleitung Solo 646 (Seite 13 von 26) (Englisch)

658827

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

Starting / Stopping the engine

- 35 - ENGLISH 13

8.2 Starting up

Please read the safety instructions before starting up

the device.

(schematic diagram)

Take off the chain guard.

Place the power tool on level ground which is free of

obstructions and make sure that the cutting tool is

not touching anything.

Place one foot in the rear handle to secure the saw

on the ground. Use one hand to firmly hold the saw

by the front handle.

Alternative way to hold the saw while starting it up

(for experienced users only):

(schematic diagram)

Firmly grasp the rear handle between your thighs.

Use one hand to firmly hold the saw by the front

handle.

You must make absolutely sure that there is no

risk of contact between the guide bar and any

part of your body.

The following instructions are intended to extend the

service life of the starter cable and the starter

mechanism:

• To start with, pull the cable carefully until a first

resistance is felt, then pull it through in a fast and

strong motion.

• Always pull the cable in a straight direction.

• Do not allow the cable to chafe on the edge of the

cable eyelet.

• Avoid pulling the cable all the way out – risk of

breaking the cable.

• Always guide the starter handle back to its starting

position – do not just let go and allow it to speed

back by itself.

A damaged starter cable can be replaced by a

specialist.

When the engine is running,

lift up the power tool

and hold it safely with both hands, then briefly

operate the throttle control to cancel the part throttle

setting.

8.3 Engine will not start:

If the engine fails to start after several attempts,

check whether all adjustments described above have

been correctly carried out, particularly that the stop

switch is not in the "0" position. Try starting once

again. The combustion chamber will be flooded, if the

engine still fails to start.

In that case we recommend you proceed as follows:

• Remove the cowl.

• Pull the spark plug cap off the spark plug.

• Remove the spark plug and dry fuel mixture from

the electrodes.

• Move the throttle lever up to full throttle. Pull the

starter handle several times (with removed spark

plug) to clear the combustion chamber.

• Move the throttle lever down to idling position, refit

the spark plug, the plug cap and the cowl.

• Repeat the starting process according to the

starting settings for a warm start.

8.4 Switching the engine off::

Release the throttle control and move the stop switch

to the "0" position.

Always make sure that the cutting tool has come

to a complete standstill before placing the

machine down.

Tip: As it can sometimes happen that, after a

brief/intermediate stop, the starting settings are not

set up correctly before the machine is restarted (in

particular, the stop switch may still be set to "0" and

the chain brake may not have been applied), we

recommend that users should get in the habit of

immediately applying the chain brake whenever the

machine is temporarily switched off and the engine

comes to a complete standstill and of setting the stop

switch back to the "Operating“ position.

As a general rule, you should always check the

starting settings before every start.

Switching the engine off in the event of a malfunction:

If – due to a malfunction of the stop switch – it is not

possible to switch the engine off, you can also close

the choke flap

(choke pulled out) to bring the

engine to a standstill. In this case do not restart the

tool – have it checked out immediately by a specialist

workshop instead!

Fig. 8

Fig. 9

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Solo 646 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Solo 646

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info