Bedienungsanleitung Solo 652 (Seite 10 von 26) (Englisch)

658828

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

Preparing the equipment for use ; Refuelling and adding oil to the chain lubrication system

ENGLISH 10 - 32 -.

5. Preparing the equipment for use

5.1 Assembly of the guide bar and chain

The chain brake must be released

when assembling the chain and adjusting the

chain tension [pull back the hand protection

(3) to the front handle (4)].

Notes for new saw chains:

Before installing a new

chain we recommend soaking it in a container (bowl)

with chain oil with anti-fling additives that help the oil

adhere to the chain.

• Undo the retaining nuts on the rail cover (12).

• Take off the rail cover (a).

• When setting up the tool for the first time, remove

the cardboard disc inserted at the factory as

transport protection underneath the rail cover

before installing the guide bar.

• On used saws, clean the rail contact surface and

the oil outlet.

• Use the chain tensioning bolt (13a / 13b) to move

the chain tensioning cam (b) to the left-hand end

stop. .Note:

Each time the guide bar is removed

and installed, adjust the chain

tension cam (b) up

to the l.h. end stop.

• Po Position the guide bar; in the process, the

chain tensioning cam (b) must fully engage in the

designated hole in the guide bar.

• Fit the chain over the sprocket and into the guide

groove of the guide bar.

o The cutting elements of the saw teeth must be on

the upper side of the rail facing towards the tip of

the rail.

o Ensure that the drive links grip correctly between

the teeth of the chain wheel and reversing wheel

at the tip of the guide bar.

• Fit the rail cover, but initially only tighten the

retaining nuts finger tight.

• After correctly adjusting the chain tension (refer to

the next section), tighten the retaining nuts as

described below.

5.2 Adjusting the chain tension

• Loosen the retaining nuts on the rail cover (12), or

if you are assembling the chain, only tighten it

finger-tight.

• Place the rail tip on a suitable wooden support

(e.g. a tree stump) and press the guide bar

upwards slightly as a result.

• Use the chain tensioning bolt (13) to set the

correct chain tension.

o Turn the chain tensioning bolt clockwise to

increase the chain tension or

o anti-clockwise to slacken the chain tension.

• The chain has the correct tension if it makes full

contact with the guide bar but can still be lifted off

the guide bar by hand by around 2 - 4 mm.

(schematic diagram)

• With the rail tip placed on a suitable surface and

the guide bar pressed up slightly, tighten the

retaining nuts with the enclosed combination tool.

Then check the chain tension again.

Always check the chain tension before starting the

device and adjust it as required. You should also

check the chain tension again and adjust it as

required once the power tool has warmed up and

again intermittently while working with the tool – but

make sure the engine is switched off first!

Important hint:

As the chain tightens again slightly when the device

cools off, slacken the chain tension a little once you

have finished work before putting the chainsaw into

storage.

6. Refuelling and adding oil to the chain

lubrication system

The tank caps for the fuel tank and the chain

lubrication oil tank are sealed by means of an O-ring.

Both tank closures should only be tightened finger-

tight, without the use of tools.

Fig. 4

Fig. 2

Fig. 3

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Solo 652 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Solo 652

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info