Bedienungsanleitung Solo 652 (Seite 12 von 26) (Englisch)

658828

Zoom out

Zoom in

Vorherige Seite

1/26

Nächste Seite

Chain brake ; Starting / Stopping the engine

ENGLISH 12 - 34 -.

7. Chain brake

When the chain brake is activated, it stops the saw

chain in a fraction of a second.

Automatic engagement:

In an emergency, the chain brake engages instantly

in response to the inertia caused by kickback.

Please note that even the highly effective

automatic chain brake cannot offer

complete protection against injury. Always

work with great care and always avoid working

situations which would put you at risk of kickback.

Manual activation:

c To manually activate the chain brake,

press the hand protection (3) forwards

towards the guide bar.

As well as providing a quick response in an

emergency situation, manual activation of the saw

chain brake is intended as a means for immobilising

the tool in all situations in which the operator cannot

knowingly control the position of the guide bar or in

which the risk of unintentional contact between the

saw chain and a foreign body or the user himself

cannot be entirely excluded. This particularly applies

to starting the engine and carrying the tool, e.g. when

assessing an object or the surroundings before

starting cutting work or when walking from one

working area to the next.

In order to avoid excessive wear, the chain brake

should not be applied until the chainsaw has come to

a standstill – except of course in an emergency.

During start-up, once the engine has started the part

throttle setting should be cancelled as soon as

possible by briefly pulling the throttle control. This

ensures that the engine does not have to work

against the blocked chain for too long under part

throttle.

d To release the chain drive (i.e. cancel the

chain brake), pull the hand protection (3) back to

the front handle (4) again

Each time, before commencing your work, check

the function of the chain brake as follows:

• Start the engine (see chapter 8)

• trigger the chain brake at idle speed

• then briefly accelerate to full throttle

• the chain should then not move.

Never operate the chainsaw if it is faulty; instead let

a service workshop check your power tool

immediately

8. Starting / Stopping the engine

Every time you pull the starter cord, observe the

correct position and the safe position of the chainsaw

in accordance with the following chapter 8.2

"Starting".

8.1 Start-up settings

Before starting the engine, apply the chain

brake to immobilise the device.

• Set the stop switch (18) to "I".

• When starting the device for the first time, or after

having completely run down the fuel tank and

refuelled, press the primer (21) several times (at

least 5 x) until fuel can be seen in the plastic

bubble.

• Before pulling the starter handle, press the

decompression valve (22) to make the starting

process easier. (Once the engine has started, the

decompression valve automatically jumps back to

the normal position.)

Cold start:

Pull out the choke (7) [this also activates

the part throttle setting, which can be

seen from the pulled-out part throttle

control pin (8)]

Slowly pull the starter handle until a first

resistance is felt, then pull it through in a

fast and strong motion.

Repeat the starting process until the engine audibly

and briefly starts up (ignites).

Then immediately press the choke back

in again. When the engine is restarted

again it then keeps running at part

throttle (visible from the part throttle

control pin).

With the engine running, briefly operate

the throttle control to cancel the part

throttle setting (the part throttle control

pin jumps back in again). The engine

will then continue to run at idle

speedter.

Warm start:

Start the engine in idle setting with the choke not

pulled out, or start it in

part throttle setting:

by pulling the choke out and pressing it

back in again [the part throttle setting is

activated as a result, which is visible

from the pulled-out part throttle control

pin (8)]

Start the engine until it runs, then briefly operate the

throttle control to cancel the part throttle setting (the

part throttle control pin jumps back in again). The

engine then runs on at idle speed.

Fig. 7

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Solo 652 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Solo 652

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info